Sonance DSP 2-150 MKII - SonARC Software: Advanced Features; Network and Identification Settings; Backup, Restore, and Print Functions; Auto On and Sleep Mode Configuration

11
Auto On
Select the Auto On method you would like to use with the blue pull
down menu. During setup it is strongly recommended that you
RLLW[OL(\[V6UTL[OVKZL[[V76>,9)<;;65[VWYL]LU[[OL
HTWSPÄLYMYVTZO\[[PUNVќ@V\JHUYL[\YUH[HU`[PTL[V[OL(\[V6U
ZL[[PUNHUKZLSLJ[[OLÄUHSTL[OVKVM(\[V6UMVY`V\YPUZ[HSSH[PVU
>OLUJVU[YVSSPUN[OLHTWSPÄLY\ZPUN07HUK09JVTTHUKZ^L
suggest using the Power Button Auto On mode. See Appendix B.
Audio
In the Audio Auto On mode, there are three sleep mode options
VќTPU\[LZOV\YZ,HJOJOHUULSOHZHUPUKLWLUKLU[ZSLLW
mode setting. The sleep mode is triggered by an audio sensing
JPYJ\P[VULHJOJOHUULSVM[OLHTWSPÄLY;OLTPUPT\TPUW\[ZLUZPUN
level is 0.5mV.
Audio Green
0U[OL(\KPV(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќHM[LY
minutes without an audio signal present on any of the channels.
>OLUHUH\KPVZPNUHSPZHWWSPLK[OLHTWSPÄLY^PSS[HRLHWWYV_PTH[LS`
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN
[OYV\NOP[ZWV^LY\WZLX\LUJL0U[OLH\KPV(\[V65TVKL[OL
sleep function is active, see sleep mode note below. This mode
complies with EU energy saving standards.
Backup Restore
The green BACKUP and RESTORE buttons take all of the settings
VM[OLHTWSPÄLYPUJS\KPUN[OL+:7ZL[[PUNZHUKLUJHWZ\SH[LZ[OLT
PU[VVULÄSL;OPZHSSV^Z`V\[V[YHUZMLY[OLZLZL[[PUNZPU[VHUV[OLY
HTWVM[OLZHTLTVKLS^P[O[OLZHTLÄYT^HYL]LYZPVU;OPZPZH
WYVWYPL[HY`ÄSL[`WLIPUÄSLHNUVZ[PJ[V7*VY4HJ
Print
The print button will output a complete list of all settings for the
HTWSPÄLY0[PZHS^H`ZHNVVKPKLH[VRLLWHIHJR\WOHYKJVW`VM
the settings for each installation.
Power Button
When sleep mode is set to OFF the channel will be on at all times.
Use the sleep mode OFF setting for audio signals like a doorbell or
paging where audio must be reproduced immediately at any time.
Voltage
0U[OL=VS[HNL(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќ
immediately when the trigger voltage has been removed. When a
=(*VY+*]VS[HNLPZZLU[[V[OLHTWSPÄLYP[^PSS[HRL
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN[OYV\NOP[Z
power up sequence. This mode complies with EU energy
saving standards.
Voltage Green
0U[OL=VS[HNL.YLLU(\[V6UTVKL[OLHTWSPÄLY^PSSWV^LYVќ
immediately when the trigger voltage has been removed. When a
=(*VY+*]VS[HNLPZZLU[[V[OLHTWSPÄLYP[^PSS[HRL
ZLJVUKZMVY[OLHTWSPÄLY[VYLWYVK\JLH\KPVHM[LYNVPUN[OYV\NO
its power up sequence. In Voltage Green mode the Ethernet
JVUULJ[PVUPZUV[HJ[P]L^OLU[OLHTWSPÄLYPZVќ;OPZTVKL
complies with EU energy saving standards.
IP Subnet Mask
The third setting in the IP SETUP section is the IP Subnet Mask.
This is an advanced network setup function. Under most
JPYJ\TZ[HUJLZ[OPZÄLSKZOV\SKUV[ULLK[VILLKP[LK
4HRPUNJOHUNLZPU[OPZÄLSKZOV\SKVUS`ILKVULI`HUL_WLYPLUJLK
network administrator.
ID Amp Mode
>OLU[OLWV^LYZ^P[JOPZ[\YULK65[OLWV^LYI\[[VUVU[OL
MYVU[VM[OLHTWSPÄLY^PSSÅHZO[VPUKPJH[L^OPJOHTWSPÄLY`V\HYL
WYVNYHTTPUN;OPZ^PSSTHRL[OLHTWSPÄLYLHZ`[VPKLU[PM`PUHT\S[P
amp installation.
6OHHS0RGH
:SLLWTVKLHSSV^Z`V\[VZLSLJ[OV^SVUN[OLHTWSPÄLY^PSSZ[H`
HJ[P]LHM[LY[OL(\[V65TL[OVKJLHZLZ
6Ɉ
When set in the OFF mode the channel will be on at all times.
Use the OFF setting for audio signals like a doorbell or paging
where audio must be reproduced immediately at any time.
After 15 Minutes
When an audio signal has not been present on a channel for 15
minutes, the channel will go to sleep. From the sleep state the
channel will take approximately 2-3 seconds to reproduce audio
again. This mode is similar to legacy Sonamp Auto-On operation.
After 3 Hours
When an audio signal has not been present on a channel for
3 hours, the channel will go to sleep. From the sleep state the
channel will take approximately 2-3 seconds to reproduce audio
again when audio is detected.. This mode works well for home
theater installations.
Info
;OLVYHUNLISVJRZHYLPUZ[HSSLYLU[LYLKKH[H,HJOÄLSKOHZH
maximum of 15 characters.
NOTE: WHEN AUDIO GREEN MODE IS ENABLED AND THE AMPLIFIER IS
ASLEEP, IP COMMANDS CANNOT BE RECEIVED.