Sony CDX-FW570 - User Manual

© 2004 Sony Corporation Printed in Thailand
3-262-851-21 (1)
Cautions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the leads under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all ground leads to a common ground
point.
•Be sure to insulate any loose unconnected
leads with electrical tape for safety.
•The use of optical instruments with this
product will increase eye hazard.
Notes on the power supply lead (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar
3 from the unit. For details, see “Removing
the protection collar and the bracket (4)” on
the reverse side of the sheet.
•Keep the release keys 5 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm
(
3
/32 in). If the catches are straight or bent outwards,
the unit will not be installed securely and may spring
out.
Installation/Connections
Instalación/Conexiones
FM/AM
Compact Disc
Player
Connection example (2)
Notes (2-A)
• Be sure to connect the ground lead before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1 To a metal surface of the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black ground lead to a
metal surface of the car first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
1 32
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
Rear speaker
Altavoz posterior
Front speaker
Altavoz frontal
1
Power amplifier
Cambiador de CD/MD
5
× 2
4
Active subwoofer
Altavoz potenciador de
graves activo
CDX-FW570
Catch
1
× 4
AUDIO OUT
FRONT
AUDIO OUT
REAR
SUB OUT (MONO)
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*
Selector de fuente*
XA-C30
* not supplied
no suministrado
2
A
B
CD/MD changer
Subwoofer activo
Rotary commander RM-X4S
Mando rotatorio RM-X4S

Summary

Connection Example

Notes for Connection Example

Notes on connecting optional power amplifiers and using the built-in amplifier.

Tip for CD;MD Changer Connection

Tip for connecting multiple CD/MD changers using an optional source selector.

Connection Diagram

Ground and Power Connections

Details on connecting ground leads, power antenna control, and power supply leads.

Amplifier and Auxiliary Connections

Connections for optional power amplifiers, car telephone interface, and illumination signal.

Accessory and Constant Power Connections

Connecting to the accessory power terminal and constant +12V power terminal.

Installation and Mounting

Bracket and Release Key Procedures

Instructions on using release keys to remove and install the bracket and protection collar.

Dashboard Mounting Example

Illustrates how to install the unit into a dashboard or center console.

Vehicle-Specific Mounting

Mounting instructions tailored for Toyota and Nissan vehicles.

Front Panel Detachment and Attachment

Detaching the Front Panel

Procedure for safely removing the front panel of the unit.

Attaching the Front Panel

Procedure for correctly reattaching the front panel to the unit.

Warning for ACC-less Ignition

Cautionary advice for installing in cars without an ACC ignition position to prevent battery drain.

Reset Button Operation

Instruction to press the RESET button after installation and connection.

Sony CDX-FW570 Specifications

General

CD Playback	Yes
MP3 Playback	Yes
WMA Playback	Yes
USB Port	Yes
Bluetooth	No
Radio Tuner	Yes
Display Type	LCD
Equalizer	Yes
Auxiliary Input	Yes
Remote Control	Yes
Detachable Faceplate	Yes
Anti-Theft Protection	Yes
Channels	4
Power Output	52 W
RMS Power Output	17 W