© 2004 Sony Corporation Printed in Korea
3-261-846-11 (1)
Cautions
•This unit is designed for negative ground 12 V
DC operation only.
•Do not get the leads under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all ground leads to a common ground
point.
•Be sure to insulate any loose unconnected
leads with electrical tape for safety.
•The use of optical instruments with this
product will increase eye hazard.
Notes on the pow er supply lead (yellow )
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in
the instructions.
•The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar
3 from the unit. For details, see “Removing
the protection collar and the bracket (4)” on
the reverse side of the sheet.
•Keep the release keys 5 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Bef ore inst alling, make sure that t he catches on
both sides of t he bracket 1 are bent inwards 2 mm
(
3
/
32
in). If the catches are st raight or bent out wards,
the unit w ill not be installed securely and may spring
out.
Installat ion/Connections
Installat ion/Connexions
FM/AM
Compact Disc
Player
Connection example (2)
Notes (2-B)
• Be sure t o connect t he ground lead bef ore
connect ing t he amplifier.
• If you connect an opt ional power amplif ier and do
not use t he built -in amplif ier, the beep sound w ill
be deact ivated.
Connection diagram (3)
1 To a metal surface of the car
First connect the black ground lead, then
connect t he yellow and red power input leads.
2 To the pow er antenna control lead or pow er
supply lead of antenna booster amplifier
Notes
• It is not necessary t o connect t his lead if t here
is no pow er ant enna or ant enna boost er, or
wit h a manually-operat ed telescopic ant enna.
• When your car has a built -in FM /AM antenna in
the rear/side glass, see “ Not es on t he cont rol
and power supply leads.”
3 To AM P REM OTE IN of an optional pow er
amplifier
This connection is only for amplif iers. Connecting
any other syst em may damage t he unit .
4 To the +12 V pow er terminal w hich is energized
in the accessory position of the ignition key
sw itch
Notes
• If t here is no accessory posit ion, connect t o t he
+12 V pow er (bat t ery) t erminal which is
energized at all t imes.
Be sure t o connect the black ground lead to a
met al surf ace of t he car f irst .
• When your car has a built -in FM /AM antenna in
the rear/side glass, see “ Not es on t he cont rol
and power supply leads.”
5 To the +12 V pow er terminal w hich is energized
at all times
Be sure t o connect the black ground lead to a
met al surf ace of t he car f irst .
2
A
B
AUDIO OUT REAR
1 32
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrat ions (non fournis)
Rear speaker
Haut-parleur arrière
Front speaker
Haut-parleur avant
1
Pow er amplifier
Amplificateur de puissance
5
× 2
4
Active subw oofer
Caisson de graves actif
CDX-R3300
CDX-R3000
Catch
1
× 4
Downloaded from: https://www.usersmanualguide.com/
To Next Page
Need help?
General
