SERVICE MANUAL
SPECIFICATIONS
DSC-1024HD
Digital Scan Converter
US Model
Canadian Model
AEP Model
Chassis No. SCC-J91B-A
MICROFILM
– Continued on next page –
Signal input
VIDEO 1 IN Composite video/reference input
BNC connector × 2 (loop-through),
75 ohms (automatic termination)
NTSC
3.58
/PAL
4.43
, 1 Vp-p typical
Black burst signal for the gen-lock
function*
S video (Y/C)
4-pin mini DIN connector × 2 (loop-
through), 75 ohms (automatic
termination)
Y: 1 Vp-p typical, sync negative
C: 0.286 Vp-p (NTSC)/0.3 Vp-p
(PAL) typical
VIDEO 2 IN RGB/component/composite video
D-sub 15-pin, 3-row x 2 (loop-
through), 75 ohms/high
impedance
R/G/B: 0.714 Vp-p
H/V or composite sync: 1 to 5 Vp-p
Y/B-Y/R-Y: 0.7 Vp-p (NTSC/PAL,
sync on Y)
Composite video: 1 Vp-p
(NTSC
3.58
/PAL
4.43
)
VIDEO 3 IN RGB/component
D-sub 15-pin, 3-row connector × 2
(loop-through), 75 ohms/high
impedance
R/G/B: 0.714 Vp-p (sync on G
acceptable)
H/V or composite sync: 1 to 5 Vp-p
Y/B-Y/R-Y: 0.7 Vp-p typical
(NTSC/PAL, sync on Y)
AUDIO IN 1, 2, 3 (L/R) RCA pin jack, more than 10 kilohms
0 dBs (1 Vrms) max.
Video processing
Capture range Horizontal rate: 15.6 to 70 kHz,
Vertical rate: 50 to 120 Hz
Preset signal Input: 10 formats
Output: 7 formats
Gen-lock output: NTSC or PAL
(See page 49.)
Video memory 1,152 × 1,152 × 24 bits (RGB total)
Sampling rate 14.3 to 40 MHz offset phase max.
(equivalent to 80 MHz sampling)
Output pixel clock 14.3 to 50 MHz max.
General
Power requirements 100 to 120 V AC, 50/60 Hz, 0.4 A
200 to 240 V AC, 50 – 60 Hz, 0.25 A
Power consumption 30 W (max. in operation)
3 W (power off)
Operation temperature 0 to 35°C (32 – 95°F)
Dimensions 424 × 44 × 354 mm (w/h/d)
(16
3
/
4
× 1
3
/
4
× 14 inches)
excluding bracket and legs
Mass Approx. 4.1 kg (9 lb 1 oz)
Supplied accessories AC power cord (1)
Signal cable (1)
Screws for mounting bracket kit MB-
510 (4)
Optional accessories
Rack mount bracket MB-510
SMF-400: D-sub 15-pin (male) to 5 BNC cable
SMF-401: D-sub 15-pin (male) to D-sub 15-pin (male) cable
Remote commander RM-854, RM-1271, RM-PJ1292, RM-PJ350
* Note on the gen-lock function
The reference signal should comply with SMPTE 170M (NTSC)
or ITU-R624 (PAL).
To Next Page
General
