Sony HVR-M25P - Page 119

HVR-M25J/M25U/M25N/M25E/M25P/M25C
6-5
Tape guide 1
(Drawing numbers: 710 to 714)
Cassette
compartment
(Drawing numbers:
851)
FL motor block
(Drawing numbers: M905, 853 to 856)
GL arm S/T block
(Drawing numbers: 810 to 817)
Coaster S/T Block
(Drawing numbers: 801 to 802)
MIC base guide
(Drawing numbers: 702)
MIC base assembly
(Drawing numbers: 701, 703, 723, 724, CN004, S004)
Drum cap
(Drawing numbers: 721)
Drum assembly
(Drawing numbers: M901)
Tape support
(Drawing numbers: 717)
Pinch arm assembly
(Drawing numbers: 718 to 720)
Capstan cover
(Drawing numbers: 819)
Capstan motor
(Drawing numbers: M903)
Tape guide 8
(Drawing numbers: 710 to 714)
Tape guide 2
(Drawing numbers: 776 to 780)
Tape guide 7
(Drawing numbers: 776 to 782)
Guide guard
(Drawing numbers: 715)
Capstan cover
(Drawing numbers: 819)
Reel motor
(Drawing numbers:
M904)
Pendulum retainer
(Drawing numbers: 705)
Pendulum
retainer
(Drawing
numbers: 705)
Pendulum arm assembly
(Drawing numbers: 706)
Brake arm S/Ratchet brake T
(Drawing numbers: 707, 708, 709)
SBR slider
(Drawing numbers: 757)
Cam motor
(Drawing numbers: M902)
Idler gear A/B
(Drawing numbers: 751, 752)
Motor holder block
(Drawing numbers: 763, 783, M902)
TG2 arm/TG2 band block
(Drawing numbers: 766, 768, 771 to 775)
TG7 arm/TG7 band block
(Drawing numbers: 767, 769, 770, 775)
Sub-slider arm
(Drawing numbers: 761)
Sub-slider
(Drawing numbers: 758)
Main cam gear
(Drawing numbers: 755)
Coupling gear (Drawing numbers: 762)
Sub-cam gear
(Drawing numbers: 756)
Pinch slider
(Drawing numbers: 760)
Loading drive lever (Drawing numbers: 759)
Main slider
(Drawing numbers: 820)
Brake arm S
(Drawing numbers: 708)
Main slider arm
(Drawing numbers: 803)
Encoder cover (Drawing numbers: 818)
MD-76 board
(Drawing numbers: 824, etc.)
Pendulum stopper assembly
(Drawing numbers: 805)
Encoder gear
(Drawing numbers: 754)
Reel table S/T
(Drawing numbers: 753)
Reel base retainer (Drawing numbers: 829)
Reel base S/T block
(Drawing numbers: 822, 823, 827, 828)
FP-248 flexible board (condensation sensor)
(Drawing numbers: 821)
Page 6-6
Page 6-10
Page 6-11
Page 6-12
Page 6-12
Page 6-13
Page 6-14
Page 6-14 Page 6-14
Page 6-12
Page 6-13
Page 6-13
Page 6-14
Page 6-15
Page 6-16 Page 6-17
Page 6-17 Page 6-17
Page 6-17
Page 6-14
Page 6-19 Page 6-19
Page 6-20 Page 6-20
Page 6-19
Page 6-17
Page 6-17
Page 6-17 Page 6-17
Page 6-16
Page 6-13
Page 6-15
Page 6-9
Page 6-9
Page 6-9
Page 6-9
Page 6-14
Page 6-15 Page 6-15
Page 6-10 Page 6-13
Page 6-12
Page 6-21
Page 6-11
Page 6-9
Page 6-10
Page 6-10
Note: When removing the MD-76 board, all the parts in the shaded
boxes ( ) of the chart need to be removed.
Find the replacement parts in Section 5, “Repair parts list (ex-
ploded views)” and attach or remove the parts in the following
order. When replacing and re-attaching the parts, adjustments are
sometimes required. Follow the instructions of each item.
Note: Drawing numbers in each box of the chart refer to the
numbers assigned to each part in the exploded views of
Section 5, “Repair parts list”.
1-3. Information (Mechanical Section)
START