KDL-26S2000
KDL-32S2000
KDL-40S2000
Sony Corporation © 2006 Printed in Japan
2-671-017-11(2)
Quick Setup Guide
For further information, see the operating instruction supplied with the TV.
Please retain this guide for your future reference.
For service and technical assistance, call our Customer Information Service Center (Toll Free):
US residents: 1-800-222-SONY (7669)
Canadian residents: 1-877-899-SONY (7669)
or visit: http://www.sony.com/TVsupport
DO NOT RETURN TO THE STORE
Making Audio/Video Connections
Your new TV includes various types of video inputs and two types of audio jacks;
composite-RCA type and digital audio (optical).
Use the outputs/inputs that are available on your components that provide the best
video/audio performances:
Connector type
HDMI (High-Definition
Multimedia Interface)
DVI
(Digital Visual Interface)
Will require an adapter to connect to this TV.
Component video
S VIDEO
Composite video
Connector type
Digital Optical
Digital Coaxial
Will require an adapter
to connect to this TV’s
digital audio output.
Analog Audio
OPTICAL
OUT
Best Audio/Video
Performance
The connection diagrams shown below and on the reverse side are recommendations only;
other possible solutions may exist. Connections that include an AV receiver can often be
complex, so check your AV receiver’s instruction manual for additional details.
See the “Cables Required” chart that appears with the diagram to determine which cables you’ll
need. Depending on the components you plan to connect, you may need to purchase extra cables.
Running Initial Setup
1
Press
POWER
to turn on the TV.
The Initial Setup screen appears.
2 Press V/v to highlight the on-screen display
language. Then press
.
The message “First please connect cable/
antenna. Do you want to start Auto
Program?” appears.
3 Press B/b to highlight “OK” then press .
The message “Auto Program” appears. Then
the message “Continue programming digital
channels?” appears. This may require 50+
minutes for completion.
4 Press B/b to highlight “OK” then press .
When Initial Setup is complete, the TV will display the total number of analog
channels or the total number of digital channels found.
To run Auto Program again at a later time
Refer to the manual on “Initial Setup” and “Auto Program” sections.
The default setting for channel selection is Cable On. For antenna connections, run the Auto
Program again after selecting Cable Off from the settings.
Initial Setup
English
Español
Français
Please select your language
Auto Program
Programmed Channel: 10
Now tuning
A
Cables Required
Splitter 1
Coaxial 3
Composite 1
Component 1
Audio 2
HD15-HD15 1
Use this diagram if you have;
VCR
Player
DVD
PC
Rear of TV
VHF/UHF
R AUDIO L
VIDEO
AUDIO
RGB
AUDIO
(MONO)
L
R
S VIDEO
AUDIO
L
Y
P
B
P
R
R
VIDEO IN
PC IN
HD/DVD IN
(1080i/720p/480p/480i)
7
6
134 5
OPTICAL OUT
AUDIO OUT
(VAR/FIX)
DVD Player
VCR
LINE IN
OUT
IN
LINE OUT
AUDIO
VIDEO
RL
Splitter
Cable
PC
B
Use this diagram if you have;
Cable Box
VCR
Player
DVD
PC
AV Receiver
or
Satellite Receiver
Cables Required
Splitter 1
Coaxial 4
Composite 3
Component 1
Audio 3
HD15-HD15 1
Rear of TV
VHF/UHF
R AUDIO L
VIDEO
AUDIO
RGB
AUDIO
(MONO)
L
R
S VIDEO
AUDIO
L
Y
P
B
PR
R
VIDEO IN
PC IN
HD/DVD IN
(1080i/720p/480p/480i)
7
6
134 5
OPTICAL OUT
AUDIO OUT
(VAR/FIX)
A/V
R
L
INPUT
LINE IN
VIDEO
VIDEO
OUT
AUDIO
OUT
TVVCRDVD
VCR
LINE IN
OUT
IN
LINE OUT
AUDIO
VIDEO
RL
DVD Player
Cable Box or
Satellite Receiver
OUT
IN
SAT IN
Splitter
Cable
PC
If your DVD player has an HDMI jack, use that
instead of the video connections shown here.
If your DVD player or satellite receiver has an
HDMI jack, use that instead of the video
connections shown here.
If you are not using a cable box or
satellite receiver, connect your cable to
the VCR’s RF IN jack.
Continued ,
To Next Page
Need help?
General