•
Tips
• Preset Dial also allows you to make a call
by
pressing a number button twice afterpressing
(CALL).
• On the "Dialed Calls," "Received Calls"
and
"Preset
Dial" menus, you can make
a call
by
pressing
(
CALL)
while the phone numberis displayed.
Presetting the volume
of
ring tone
and talker's voice
You
can preset the volume level
of
the ring tone
and talker's voice.
To
adjust the ring tone:
Rotate the joystick while the phone is ringing.
"Ring Vol" appears and ring tone volume is set.
To
adjust the talker's voice:
Rotate the joystick during a call. "Talk Vol"
appears and the talker's voice volume is set.
Sending
DTMF
(Dual Tone Multiple
Frequency) tones
You
can send DTMF tones.
To
send DTMF tones, use the joystick or press
the required number buttons
(0
- 9, *or
#)
on
the card remote commander during a call.
Receiving
calls
When receiving a call, ring tone is output from
your car speakers.
For details on the settings for receiving a call and
during a call, see "Setting a handsfree device" on
page
17.
1 When receiving a call, press
@QJ,
(
MENU)
or
(Bluetooth).
It1G~-
- (B'U9tOO'h)
I,"~~~
The phone call starts.
To
reject a call
Press
(OFF).
Tips
•
If
you
set
"Auto Answer" to on, the phone call is
automatically started in the
set
time (page
17).
•
If
(
CALL)
is pressed during a call, the handsfree
function is deactivated,
and
the microphone
and
speaker
of
the cellularphone are activated. In this
case, the Bluetooth connection may become
disconnected depending on the cellularphone.
Note
Even
if
the call
is
ended, the Bluetooth connection is
not
canceled.
Using the
Phonebook
Receiving phonebook data from a
cellular phone
1 Select "Phone Settings" from the Bluetooth
function menu.
2 Select "Receive PB."
"Waiting..." appears.
3 Send the phonebook data by operating the
cellular phone.
"Data Receiving
...
" appears while receiving
the phonebook data.
"Complete" appears when receiving
is
complete.
Notes
• Before receiving phonebook data, disconnect
any
cellularphone
or
audio device.
•
To
cancel the transfer
of
phonebook data, operate
the cellularphone. Transfer cannotbe canceled from
this unit.
Storing the numbers from "Dialed
Calls"
or
"Received Calls"
1 Select "Dialed Calls" or "Received Calls"
from the CALL menu.
2 Select the phone number to store, then select
"Save."
The "Contact Name" display appears.
3 Input a name.
Up to 20 characters can be input.
4 Select "Save?"
~
"yes."
Note
Up to 50 phone numbers can be stored in the
Phonebook.
If
you try to register more than 50
numbers, "Memory Full" appears.
Deleting from the phonebook
1 Select "Phonebook"
~
"Contact List" from the
CALL menu.
2 Select the name to delete.
3 Select "Delete Contact"
~
"yes."
To
clear all phonebook data, select "Delete All"
in step
1.
After clearing, confirm that all
phonebook data has been cleared properly.
16
Ending
calls
1 Press
(OFF).
When the call ends, talk time appears for a
few seconds.
Changing a name in the phonebook
1 Select "Phonebook"
~
"Contact List" from the
CALL menu.
2 Select the name to change.
3 Select "Edit Name," then input a new name.
To Next Page
Loading...
Need help?
General
