Sony SA-WX9000F User Manual

SERVICE MANUAL
Sony Video & Sound Products Inc.
Amplier section
(X9000F: US)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
Front L + Front R:
With 4ohms loads, both channels
driven, from 200 - 20,000Hz; rated
35W per channel minimum RMS
power, with no more than 1% total
harmonic distortion from 250mW to
rated output.
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W
(per channel at 4ohms, 1kHz)
(X9000F: CND/XF9000: AEP, UK)
POWER OUTPUT (rated)
Front L + Front R: 60W + 60W
(at 4ohms, 1kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker blocks: 100W
(per channel at 4ohms, 1kHz)
Inputs
HDMI IN*
ANALOG IN
TV IN (OPT)
Outputs
HDMI OUT (TV (ARC))*
*HDMI IN and HDMI OUT (TV (ARC)) jacks
support HDCP 2.2 protocol. HDCP 2.2 is
newly enhanced copyright protection
technology that is used to protect
content such as 4K movies.
HDMI Section
Connector
Type A (19pin)
USB section
(USB) port:
Type A (For connecting USB memory)
BLUETOOTH section
Communication system
BLUETOOTH Specication version 4.2
Output
BLUETOOTH Specication Power
Class1
Maximum communication range
Line of sight approx. 30m
1)
Maximum number of devices to be
registered
9 devices
Frequency band
2.4 GHz band (2.4GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH proles
2)
A2DP (Advanced Audio Distribution
Prole)
AVRCP (Audio Video Remote Control
Prole)
Supported Codecs
3)
SBC
4)
, AAC
5)
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency
32kHz, 44.1kHz, 48kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic elds around a
microwave oven, static electricity,
cordless phone use, reception
sensitivity, the operating system,
software applications, etc.
2)
BLUETOOTH standard proles indicate
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
4)
Abbreviation for Subband Codec
5)
Abbreviation for Advanced Audio
Coding
Front L/Front R speaker block section
Speaker system
Full Range speaker system, Acoustic
suspension
Speaker
40mm × 100mm (1 5/8 in. × 4 in) cone
type
General
Power requirements
120 V AC, 60 Hz (X9000F: US, CND)
Power consumption
On: 38W
[Bluetooth Standby] - [On]: Less than
2W
[Bluetooth Standby] - [O]: Less than
0.5W
Dimensions* (approx.) (w/h/d)
930mm × 58mm × 85mm (36 5/8 in ×
2 3/8 in × 3 3/8 in)
*Not including projection portion
Mass (approx.)
2.5kg (5 33/64 lb)
Frequency band
2.4GHz (2.4000GHz - 2.4835GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Design and specications are subject to
change without notice.
Wireless Transmitter/
Receiver Section
220 V - 240 V AC, 50 Hz/60 Hz
(XF9000: AEP, UK)
What’s in the Box
t#BS4QFBLFS
t4VCXPPGFS
t3FNPUFDPOUSPM
t3TJ[F"""CBUUFSZ
t)%.*DBCMFTVQQPSUTUIFTQFDJöDBUJPO
equal to Premium High Speed HDMI
Cable with Ethernet) (1) (X9000F: US, CND)
t0QUJDBMEJHJUBMDBCMF9'"&16,
t8"--.06/55&.1-"5&
t4UBSUVQ(VJEF
t0QFSBUJOH*OTUSVDUJPOT
HT-X9000F/XF9000
SA-X9000F/XF9000
SPECIFICATIONS
HT-X9000F/XF9000
SOUND BAR
SA-X9000F/XF9000
ACTIVE SPEAKER SYSTEM
9-896-483-01
2018A33-1
©
2018.01
US Model
Canadian Model
HT-X9000F/SA-X9000F
AEP Model
UK Model
HT-XF9000/SA-XF9000
Ver. 1.0 2018.01
• All of the units included in the HT-X9000F
(SA-X9000F/SA-WX9000F/Remote
control) or HT-XF9000 (SA-XF9000/SA-
WXF9000/Remote control) are required
to confi rming operation of SA-X9000F/
XF9000. Check in advance that you have
all of the units.
COMPONENT MODEL NAME
HT-X9000F HT-XF9000
Bar Speaker (Active Speaker System) SA-X9000F SA-XF9000
Subwoofer (Active Subwoofer) SA-WX9000F SA-WXF9000
• Please refer to service manual separately issued for Subwoofer.
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Photo: SA-X9000F

Sony SA-WX9000F Specifications

General

Brand	Sony
Model	SA-WX9000F
Category	Speaker System
Language	English

Summary

SERVICING NOTES

UNLEADED SOLDER

Characteristics and handling of lead-free solder.

FUSE REPLACEMENT AND SAFETY PROCEDURES

Precautions for fuse replacement, discharge processing, safety checks, and leakage testing.

OPERATION PREPARATION AND MODEL IDENTIFICATION

Preparing for operation and identifying model variations.

SYSTEM PROTECTION INDICATORS

Indicator behavior when protection mode is active.

DISASSEMBLY

DISASSEMBLY FLOW

Visual guide to the disassembly sequence of the set.

CABINET AND SPEAKER DISASSEMBLY

Procedures for disassembling cabinet sections and speakers.

BOARD AND MODULE REPLACEMENT

Steps for replacing Bluetooth module, SK1 boards, and main chassis.

MAIN, AMP, AND POWER BOARD REPLACEMENT

Detailed procedures for replacing main, amplifier, and power boards.

TEST MODE

Button and LED position

Describes button and LED locations for test modes.

FACTORY INITIALIZE

Resets all unit settings to their factory defaults.

USB UPDATE

Firmware update procedure using USB memory.

DEMO MODE OPERATIONS

Procedures for entering, customizing, and releasing demo mode.

PANEL TEST

Checking LED lighting state and key input.

SERVICE MODE SETUP

Setting up and using the service mode with a TV monitor.

TROUBLESHOOTING

PROTECTION MODE ISSUES

Troubleshooting steps when the protection mode is activated.

HDMI NO AUDIO/VIDEO OUTPUT

Diagnosing and resolving issues with HDMI audio and video output.

SOUND NOT OUTPUTTED

Troubleshooting steps when no sound is produced.

POWER NOT TURNED ON

Diagnosing and resolving power-on issues.

SOUND NOT OUTPUTTED OF ARC

Troubleshooting steps when ARC sound output is not working.

SUBWOOFER NOT LINKED

Diagnosing and resolving issues with subwoofer linking.

DIAGRAMS

HDMI SECTION BLOCK DIAGRAM

Block diagram of the HDMI section, showing signal paths.

MAIN SECTION BLOCK DIAGRAM

Block diagram of the main section, illustrating circuitry.

AMPLIFIER SECTION BLOCK DIAGRAM

Block diagram of the amplifier section, detailing signal flow.

PANEL/POWER SUPPLY BLOCK DIAGRAM

Block diagram of the panel and power supply circuitry.

PRINTED WIRING BOARDS AND SCHEMATICS

Layouts of printed wiring boards and schematic diagrams for key components.

EXPLODED VIEWS

FOOT SECTION

Exploded view of the foot section with parts list.

TOP CABINET SECTION

Exploded view of the top cabinet section with parts list.

BOTTOM CABINET SECTION

Exploded view of the bottom cabinet section with parts list.

MAIN BOARD SECTION

Exploded view of the main board section with parts list.

SK1 AMP BOARD SECTION

Exploded view of the SK1 AMP board section with parts list.

POWER BOARD SECTION

Exploded view of the power board section with parts list.

ELECTRICAL PARTS LIST

MAIN AND POWER BOARD PARTS

List of electrical components for the main and power boards.

SK1 AMP BOARD PARTS

List of electrical components for the SK1 AMP board.

ACCESSORIES AND CABLES

List of included accessories and cables.