Operating
through
menus
There are fi\'e
buttons for
menu operations
on the front
of
the
monitor. To display
the main menu,
first press
MENU.
The buttons you
can use
appear at
the bottom of the
menu
screen.
Functions
of the
buttons
Button
To
select
menu
To
adjust
menu item
item
selected
MENU
EXIT
ENTER
SELECT
T
return to
the
previous
menu
decide a
selected
item
move the
cursor
()
upwards
mo\'e
the
cursor
()
downwarcfs
return
to
the previous
menu
select
an
item
increase selected value
decrease selected wilue
reset
current adjustment
value
to the factory
setting
(The
abox'C items
in
white type correspond to
the marks
in
the
menu.)
front of
monitor
B' C;
COMPONENT SOI
LINE/
EXT
RGB
SYNC
.
.
ami
BLUE
UNDER
HV
ONLY SCAN
DELAY
MENU
rilHLli
lan
ENTER
reset
buttons
for
button
menu
operations
[T]
Main menu
Select an item
and press
ENTER to go to
the following
menu.
[
2
]
CHROMA SET
UP menu
Set to
ON to adjust
the
internal decoder for
CHROMA
and PHASE
(NTSC signal
only) after
AUTO
ADJUST
(E).
'
|OFF|
[
3
]
COLOR
TEMP/BAL menu
Select
the
color temperature
from among
65()0K, 9300K
and
USER.
USER is set to
6S00K in the factory
setting.
You
can
acfjust or change the
color temperature
in USER
mocfe (a
measuring
instrument is needed),
[h.SOOK]
0
CAPTION
VISION
menu
The
iTionitor
can display
the signal with
Caption
Vision.
To
display it,
select the
caption
U
pe in this
menu.
[OFF]
[
5
]
USER
CONFIG
1 menu
Select an
item tci
adjust. To go to
the USER
COXFlCi 2
menu,
select
NEXT P.ACE.
[6]
USER
CONFIG 2 menu
Select
an item to adjust. To go to the USER CONFIG
1
menu select PREVIOUS
PAGE.
[7]
AUTO ADJUST
screen
Select the color bar
signal (full, SMPTE, ElA) and press
ENTER to start auto
adjusting for CHROMA SET UP
(NTSC signal only).
d]
ADJUST GAIN screen
Adjust
GAIN in USER mode.
[g]
ADJUST BIAS
screen
Adjust
BIAS in USER mode.
01
COLOR TEMP
RANGE menu
Select the
color temperature range in USER mode.
[50U0K40000K]
[H] COLOR
SYSTEM DISPLAY menu
Sefect the color swstem
display mode. In
AUTO,
the
kind
of
color system being used appears on the
screen each
time you
change the signal input.
[AUTO]
111
358
TRAP FILTER menu
Color spill or color noise
may
be
eliminated if you select
ON (N
rSCv^s signal
only). [OFF]
0
SUB
CONTROL screen
You can finely adjust the controls
on the front panel.
CONTR.AST, BRIGHT,
CHROMA and PHASE
control
has a click at the center
of its adjustment range. You can
acJjust the
setting
/if
the click position u'ith this feature.
HU
USER
PRESET menu
You can preset each
control
to a
desired level and set it.
If you set USER PRESE T
t/i
ON, the REMOTE indicator
lights up
and the controls on the front panel do not
work.
The
monitor operates
with
the
internal memory
settings. For
adjustment, select PRESET
ADJUST.
[OEF]
01
PRESET
ADJUST screen
Adjust
CONTRAS!
,
BRIGHT, CHROMA, PHASE,
VOLUME,
APERTURE in USER PRESE
I
.
01
V HOLD screen
Adjust the vertical hold
if the picture rolls
x
ertically.
When
vou cannot
read the display, select the input that
is not connected.
01
COMPONENT LEVEL
menu
Select the component
level from among three modes.
NIO/SMPTE
for 100/0/
11)0/0 signal
BETA 7.5
for 100/7.5/75/7.5
signal
BETA
0 for 100/0/75/0
signal
[BETA
7.5|
01
NTSC SETUP LEVEL menu
Select the NTSC setup le\ el
from two modes. I he 7.5
setup lex'el is mainly used in
north America. The
0
setup
lex'el
is mainly used in
japan.
[7.5]
01
ACC menu
Set ACC (Auto Color
Control) circuit on or off. When the
fine adjustment is needed, set .ACC to
OFF. N'ormalh’ set
it to ON.
|ON|
m
LANGUAGE menu
You can select the menu language
from among the
fix
e
languages (English, German,
French, Italian,
Spanish) on
the menu.
lENGLISI
1]
(1
I
indicates
the factiirx setting
position.)
7
English
To Next Page
Loading...
Need help?
General