Soyal AR721U661U721K hardware operation guide
Revision: V1
Date released: 1 Nov 2006
UM_Soyal721KP721U661UV1
Access Control System
1
Table of Contents
1. Main Feature ------------------------------------------ 2
2. AR-721U Installation ------------------------------------------3
2.1 Steps
2.2 Installation Notice
2.3 Terminal Cable ------------------------------------------4
2.4 PCB board ------------------------------------------5
2.4.1 No waterproof
2.4.2 Waterproof
2.5 Installation diagram -------------------------------------------6
2.5.1 AR-721U & AR-721H
2.5.2 AR-721U & AR-727H -----------------------------------------7
2.5.3 AR-721U & AR-821EF ---------------------------------------- 8
2.5.4 AR-721U & AR-829E -----------------------------------------9
3. AR-721K Installation ---------------------------------------10
3.1 Steps
3.2 Installation Notice
3.3 Terminal Cable ------------------------------------------11
3.4 PCB board
3.5 Installation diagram ----------------------------------------12
3.5.1 AR-721K & AR-721H
3.5.2 AR-721K & AR-727H -----------------------------------------13
3.5.3 AR-721K & AR-821EF ----------------------------------------14
3.5.4 AR-721K & AR-829E ---------------------------------------- 15
4. AR-661U Installation --------------------------------------- 16
4.1 Installation Notice
4.2 Terminal Cable
4.3 Installation diagram ----------------------------------------17
4.3.1 AR-661U & AR-721H
4.3.2 AR-661U & AR-727H ----------------------------------------18
4.3.3 AR-661U & AR-821EF ----------------------------------------19
4.3.4 AR-661U & AR-829E -----------------------------------------20
4.4 The standalone controller do anti-pass-back with 2 pcs of AR-661U ---------21
4.5 Testing table of AR-661U Reading Range depends on tags --------
5 Troubleshooting ----------------------------------------24
6 Return of Products / Warranty
2
1. Main Features
Easily integrated with soyal or other access control systems.
Programmable various outputs formats Wiegand , magstripe or serial.
Built-in watchdog to prevent the system from halting
A bi-color LED indicator and a beep sound.
Item AR-721U AR-721K AR-661U
RF Frequency 125KHz 125KHz / 13.56MHz
125KHz
Power
Requirement
9-16VDC 12-18VDC
125KHz 80mA Power
Consumption
50mA
13.56MHz
0.72W
350 mA
Communication
Interface
WG 26 / 34, ABA-II, ASYNC, OMRON
Baud Rate 9600 bps (N, 8, 1)
Environment -20°C to +75°C
Proximity
Reading Range
3-8cm 10-18cm (125K) /
3-8cm (13.56M)
33-60cm
Indicator A bi-color LED and a
beeper
A bi-color LED and
a beeper
Three LED and a
beeper
Keypad - Yes -
Waterproof Option - Yes
Color Dark Pearl Gray / Silver Dark Pearl Gray
Dimensions
(mm)
81(H)*43(W)*18(D) 111(H)*77(W)*26(D)
228(H)*228(W)*38(D)
Weight (g) 40±5 90±10 1,000±50
Housing
Material
ABS
3
2. AR-721U Installation
2.1 Steps
1. Use the screwdriver to screw the mounting plate on the wall.
2. Pull cable ends through the access hole in the mounting plate. AR-721U must be
connected before power is applied to the single door controller.
3. Attach the AR-721U to the mounting plate.
4. Apply power. The red LED will flash once and the beeper will sound.
2.2 Installation Notice
1. AR-721U is narrow enough to mount to most mullions and door frames.
2. Single door controller locate inside the secure area for use as an exit controller, the
auxiliary reader locate exterior wall for use as an entrance reader, but not directly
behind single door controller. For best reading distance, offset the single door
controller and auxiliary reader by about 50 cm above and 12 m below (suggestion
value).
3. Normally, AR-721U will read a Card / Key Tag at up to 8 cm. However, when
AR-721U reader is mounted directly on a metal surface, the reading distance
decreases slightly. To reduce this effect, install wood or plastic between the
mounting surface and mounting plate, this will restore most of the reading distance.
To Next Page
Need help?
General
