Speakman SC-3084-LD - User Manual

INSTRUCTIONS FOR MODELS
92-SC-3084-LD-R1
For additional assistance or service please contact:
SPEAKMAN
®
Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerservice@speakman.com
www.speakman.com
SC-3084-LD
SC-3084-LD-E
TOOLS AND SUPPLIES
IMPORTANT
SAFETY TIPS
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
MAINTENANCE
Your new Lavatory Faucet is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. Avoid
abrasive cleaners, steel wool, and harsh chemicals
as these will dull the finish and void your warranty.
WARRANTY
Additional warranty information can be found at:
www.speakman.com
Adjustable
Wrench
Slip Joint
Wrench
Phillips
Screwdriver
Silicone
or Sealant
•Be sure to read instructions thoroughly before
beginning installation.
•This installation manual covers several models.
While the appearance of your faucet may vary, the
installation steps required are the same as shown in
this manual.
•This faucet has an operating range of 20-80 psi.
Do not overtighten any connections or damage
may occur.
Supply
Hoses
Tubing
Cutter
Solder Kit
Thread Seal
Tape
Basin
Wrench
HELPFUL TOOLS & SUPPLIES:
1
Unthread and remove one trim collar to verify the
cold or hot valve. The cold valve will be marked
BLUE, and the hot valve will be marked RED.
Orient the faucet base so the “BLUE” valve is on
the right hand side. Reinstall the Trim Collar.
BLUE
2
Apply Silicone or sealant to base of faucet.
3
Position faucet onto mounting surface and press
down firmly to set the sealant.
4
From beneath sink, install Cup Washers (1) and
Shank Nuts (2) onto Shanks of Faucet. Wrench
tighten. From above sink remove excess sealant
from around the base of the faucet.
5
Connect water supplies to faucet inlets
(½-14 NPSM) and wrench tighten.
NOTE: Supply Lines and Shut-Off Valves not included.

Summary

Tools and Supplies for Installation

Essential Tools List

Lists adjustable wrench, slip joint wrench, Phillips screwdriver, silicone sealant, and basin wrench for installation.

Helpful Tools and Supplies

Includes supply hoses, solder kit, tubing cutter, thread seal tape, and basin wrench for faucet installation.

Faucet Installation Steps

Identify Valve Orientation

Unthread trim collar, verify blue (cold) and red (hot) valves, orient faucet base with blue valve on the right.

Apply Sealant to Faucet Base

Apply silicone or sealant to the base of the faucet before mounting it.

Mount Faucet and Set Sealant

Position the faucet onto the mounting surface and press down firmly to set the sealant.

Secure Faucet from Under Sink

Install cup washers and shank nuts from beneath the sink and tighten with a wrench.

Connect Water Supply Lines

Connect water supplies to faucet inlets (1/2-14 NPSM) and tighten with a wrench.

Install Gooseneck Spout

Attach the gooseneck spout to the faucet body, using a lock washer for a rigid, non-swivel feature.

Install Handles and Trim

Install trim sleeves, handles, lock washers, and handle screws, then insert index buttons (blue right, red left).

Flush Water Lines

Turn on water supplies and flush both cold and hot cartridges for one minute, checking for leaks.

Install Aerator or Spray Outlet

Turn off handles, install the supplied 1.5 gpm aerator or 0.5 gpm spray outlet with an aerator wrench.

Important Information and Safety

Installation Precautions

Avoid overtightening connections; installation steps are consistent across models, read instructions thoroughly.

Operating Range and Safety

Faucet operates at 20-80 psi. Cover drain and wear eye protection when cutting pipe.

Maintenance and Warranty

Faucet Cleaning

Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals.

Warranty Details

Additional warranty information can be found on the official website.

Repair Parts List

Part Identification

Lists item numbers, part numbers, and descriptions for faucet components like valve groups and aerators.

Rough-In Diagram and Dimensions

Faucet Dimensions

Provides detailed measurements for the faucet spout, handles, and base, in inches and millimeters.

Lavatory Rough-In Specifications

Details minimum distances required from the wall and ledge for faucet mounting (e.g., 2" to wall, 2" to ledge).

Speakman SC-3084-LD Specifications

General

Model	SC-3084-LD
Type	Showerhead
Flow Rate	2.5 GPM
ADA Compliant	Yes
Finish	Polished Chrome
Material	Brass
Installation Type	Wall Mounted