SPEC-D Tuning LHP-JET99JM-8-TM

Need help?

Do you have a question about the SPEC-D Tuning LHP-JET99JM-8-TM and is the answer not in the manual?

Summary

Volkswagen Jetta Projector Headlights Installation

Tools and Supplies Required

Lists necessary tools and supplies for the headlight installation process.

Open the Hood

Begin the installation by opening the vehicle's hood.

Remove Top Plastic Shielding

Remove protective plastic shielding located above the headlight assembly.

Remove Front Grille

Carefully lift and remove the front vehicle grille.

Remove Headlight Clips

Detach the top and bottom clips securing the headlight assembly.

Remove Bumper Mounting Bolts

Unscrew bolts located under the fender and in the fog light opening.

Slightly Pull Out Bumper

Gently pull the bumper forward to access the headlight's lower area.

Disconnect Headlight Connector

Use a flathead screwdriver to disconnect the electrical connector.

Remove Top Headlight Bolts

Unscrew the two bolts located on the top of the headlight assembly.

Remove Old Headlight

Carefully pull the existing headlight assembly out of the vehicle.

Connect New Headlight Connector

Connect the electrical harness to the new projector headlight.

Install New Headlight Assembly

Position the new projector headlight and secure it with bolts.

Reinstall Bumper Mounting Hardware

Secure the bumper by installing bolts below the headlight, at fog light openings, and under the fender.

Reinstall Front Grille Clips

Reattach the top and bottom clips to the front bumper.

Reinstall Front Grille

Place the front grille back onto the vehicle.

Reinstall Top Plastic Shielding

Put the plastic shielding back onto the top of the headlight.

Installation Complete

The headlight installation process is now finished.

Overview

Function Description
Important Technical Specifications
Usage Features (Installation Process Overview)
Maintenance Features (Safety and Best Practices)

This document provides installation instructions for Spec-D Tuning Projector Headlights designed for the 1999-2004 Volkswagen Jetta.

Function Description:

These projector headlights are aftermarket replacement units intended to enhance the lighting performance and aesthetic appeal of the specified Volkswagen Jetta models. Projector headlights typically offer a more focused and controlled light beam compared to traditional reflector-style headlights, potentially improving visibility and reducing glare for oncoming drivers. The installation process involves replacing the vehicle's original headlights with these new projector units.

Important Technical Specifications:

Compatibility: Specifically designed for 1999-2004 Volkswagen Jetta models.
Part Numbers:
- LHP-JET99JM-8-TM
- LHP-JET99-8-TM
Required Tools and Supplies for Installation:
- 3/8" Drive Ratchet
- 1/4" Drive Ratchet
- 6" Long 3/8" Drive Extension
- 6" Long 1/4" Drive Extension
- T30 Socket
- T25 Socket
- Phillips Screwdriver
- Flathead Screwdriver

Usage Features (Installation Process Overview):

The installation process is detailed across 28 steps, requiring the removal of several vehicle components to access and replace the headlights. Key steps include:

Preparation:
- Open the hood.
- Remove plastic shielding from the top of the headlight.
- Pull up the grille.
Bumper and Fender Component Removal:
- Remove two clips located behind the grille (top and bottom).
- Remove two bolts underneath the fender.
- Remove bolts from the fog light opening.
- Gently pull out the bumper slightly to access the bottom of the headlight.
Headlight Removal:
- Use a flat-tip screwdriver to disconnect the electrical connector from the headlight.
- Remove two bolts on top of the headlight.
- Gently pull out the existing headlight.
New Headlight Installation:
- Connect the electrical connector to the new projector headlight. (Note: If the headlights have HALO or L.E.D. features, refer to separate "Halo and L.E.D. installation instructions"; otherwise, this step can be skipped for those specific features).
- Gently install the projector headlight into its original spot and fasten it with the bolts.
- Install the bolts below the headlight between the bumper.
Reassembly:
- Gently push the bumper back into its original position.
- Install the bolts into the fog light opening.
- Install the bolts underneath the fender.
- Install the bottom clip on top of the front bumper.
- Install the top clip.
- Install the two clips that were previously removed.
- Put the grille back.
- Put the plastic shielding back on top of the headlight.
Completion: Repeat the entire process (steps 1-27) for the opposite side of the vehicle.

Maintenance Features (Safety and Best Practices):

The manual emphasizes several important safety and maintenance considerations:

Professional Assistance: If any difficulties arise that are not covered by the instructions, users are advised to seek advice from a local auto shop.
Personal Protective Equipment: Always wear protection (e.g., gloves, eye protection) when working on the vehicle.
Assistance for Bumper Removal: An assistant is helpful when removing the front bumper to prevent damage.
Careful Handling: Exercise caution when working with the bumper or other body parts to avoid scratching the vehicle's paint or surfaces.
Halogen Bulb Safety: Do not make direct contact with the halogen bulb or the wire assembly until the unit has cooled down after use, as they can be extremely hot and cause burns. This also helps prevent contamination of the bulb surface, which can shorten its lifespan.