EasyManua.ls Logo

Speck pumps ES90-II VSP - User Manual

Default Icon
28 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation, Operation, and Service Manual
1.1 THP Dual Voltage Series
Variable Speed Pool Pump
Motor Version 2.0
02/2019

Table of Contents

Questions and Answers

  • C
    Cory MurphyAug 9, 2025
    What to do if my Speck pumps Water Pump will not prime?
    • P
      Patrick CoxAug 9, 2025
      If your Speck pumps Water Pump won't prime, it could be due to several reasons. First, check for suction air leaks by ensuring the see-through lid and o-rings are clean and correctly placed, and hand-tighten the lid. Also, tighten all pipes and fittings on the suction side. Ensure the water level in your pool is high enough for flow through the skimmer and that the strainer tank is full. Open all valves, clean the skimmer and strainer tank, and inspect the pump for impeller clogging. Finally, check the motor voltage; if it's too low, the pump won't run.
  • J
    Jessica PalmerAug 19, 2025
    Why my Speck pumps ES90-II VSP motor does not turn on?
    • G
      Gary JacksonAug 19, 2025
      If the motor of your Speck pumps Water Pump isn't turning, it could be due to a lack of power or a jammed pump. Ensure all power switches are on and the fuse or circuit breaker is properly set. Check the timer setting. Inspect the motor wiring at the terminal. With the power off, try turning the shaft; if it doesn't spin freely, the pump may need disassembly and repair.
  • S
    Sabrina GreeneAug 29, 2025
    How to fix low flow in Speck pumps Water Pump?
    • D
      Deborah IngramAug 29, 2025
      Low flow in your Speck pumps Water Pump can be caused by a dirty filter or a suction leak. Backwash the filter when the filter pressure is high, or clean the cartridges. Also, check for suction leaks.

Summary

1.1 THP Dual Voltage Series

1 Important Safety Instructions

General Safety Precautions and Warnings

Covers critical safety rules including child supervision and electrical shock risks.

Electrical Safety: GFCI, Grounding, and Bonding

Details GFCI requirements, grounding, and bonding for safe electrical operation.

General Safety Guidelines

Entrapment Hazards and Suction Outlet Safety

Highlights risks from suction outlets, hair entanglement, and the need for clear debris.

3 Installation Information

Preparation, Location, and Piping

Covers pump inspection, location selection, and piping installation guidelines.

Pipe Sizing Recommendations

Plumbing and Electrical Installation Details

Bonding and Grounding Procedures

Explains essential bonding and grounding steps for safe operation.

Electrical Installation and Wiring

Outlines the safe and proper methods for electrical installation and wiring.

Voltage Checks and Pressure Testing

Ensuring Correct Voltage and Pressure Test Safety

4 Operation

Pump Startup and Priming Procedures

Step-by-step instructions for initial pump startup, filling, and priming.

Critical Operation Safety Warnings

Programming and Control Menu Navigation

Schedule (SCHE) Menu Configuration

Normal Operation and Default Settings

Maintenance Procedures and Winterizing

6 Troubleshooting

Controller Error Code Interpretation

Lists and explains various error codes displayed by the pump controller.

General Pump Troubleshooting Guide

Diagnosing and Resolving Common Pump Issues

Covers common problems like no prime, motor not turning, and low flow.

Impeller Blockage and Mechanical Seal Replacement

Impeller and Mechanical Seal Service Procedures

Motor Replacement Procedure

7 Product Specifications

8 Limited Warranty

Initial 90-Day Warranty Terms and Conditions

Extended Warranty Options and Eligibility

Warranty Limitations and Disclaimers

Speck pumps ES90-II VSP Specifications

General IconGeneral
Voltage230V
Maximum Flow Rate90 GPM
Max Flow Rate90 GPM
Pipe Size2 inch
Frequency60 Hz
Inlet Diameter2 inch
Outlet Diameter2 inch

Related product manuals