What to do if Spectra Logic Storage has problems reading and writing data?
If you are experiencing issues with reading and writing data, consider the following: * Ensure the cartridge is write-enabled before importing it into the library. * If the cartridge is old, try using a new one. * Clean the tape drive(s).
What to do if Spectra Logic Storage has sporadic errors when using direct-attach SCSI tape drives?
If you encounter sporadic errors, ensure that the SCSI bus connected to each tape drive is properly terminated at both ends.
What to do if Spectra Logic T Spectra T50e Storage additional devices on the SCSI bus are not properly terminated?
Ensure that only the devices at the two physical ends of the bus are terminated.
What to do if Spectra Logic T Spectra T50e LTO-4 tape drive has SCSI connection issue?
Connect a wide Ultra 3 Active SCSI terminator to the second SCSI connector on the tape drive; do not daisy-chain LTO-4 SCSI tape drives.
General| Category | Tape Library |
|---|---|
| Tape Technology | LTO |
| Drive Slots | 2 |
| Number of Slots | 50 |
| Interface | SAS |
| RAID Support | No |
| Connectivity | SAS |
| Operating System Compatibility | Windows, Linux |
| Supported Media | LTO-7, LTO-8 |
| Power Supply | Dual redundant power supplies |
| Encryption | Yes, AES 256-bit encryption |
| Form Factor | Rack-mountable |
| Number of Drives | Up to 2 |
Details the target audience for this user guide, assuming familiarity with data backup and tape media.
Lists other documents for additional information about the Spectra T50e library and its tape drives.
Explains the conventions used in the manual to highlight important information such as notes, cautions, and warnings.
Describes the key features of the Spectra T50e library, including media storage, magazines, expansion slots, and bar code labels.
Details the front panel, interior, and rear panel components of the Spectra T50e library.
Provides an overview of the library's management features, including the Library Controller, Remote Library Controller, User Security, and AutoSupport.
Covers essential preparation steps before installing the library, including checking the environment and host computer.
Provides step-by-step instructions for safely unpacking the library and its components from the shipping boxes.
Guides users through the process of installing the library, covering both rack-mount and tabletop configurations.
Provides guidelines for connecting SCSI tape drives, including bus length restrictions and termination requirements.
Explains how to connect Fibre Channel tape drives to a Fibre Channel hub, switch, or directly to the host or HBA.
Details the steps required to log into the library's user interface after powering it on.
Describes the procedure for powering the Spectra T50e library on and off using the front panel power button.
Explains how to access, log into, and log out of the library's user interface using the touch screen or web browser.
Details the information displayed on the status bar, including menu, messages, current time, current user, and IP address.
Describes the three keyboard options for entering information: Remote Access, External Keyboard, and Soft Keyboard.
Explains how to configure library users, understand user groups, and manage security privileges for library access.
Details how to access the library's configuration screens to modify system settings.
Guides users on configuring library name, refresh rate, web server port, online access, and automatic configuration save settings.
Details how to manually back up the library's configuration using the Save Library Configuration utility.
Describes how to view the library's cartridge inventory and manage media.
Explains the procedures for importing and exporting cartridges using the library's interface.
Provides instructions on how to add a cartridge capacity sled to expand library storage.
Details the steps required to remove a cartridge capacity sled from the library.
Explains how partitions divide the library logically into virtual libraries for resource management.
Guides users through the process of creating a new partition, including defining initial settings and assigning resources.
Details how to edit the number of storage slots and assign tape drives to a partition.
Provides an overview of AutoSupport functionality for contacting users and submitting support tickets.
Guides users on configuring AutoSupport, including mail recipients and profiles for troubleshooting.
Details the steps to open a new support ticket with SpectraGuard Technical Support using the AutoSupport system.
Provides an overview of how BlueScale Media Lifecycle Management (MLM) works for proactive media health monitoring.
Guides users on enabling and configuring BlueScale Media Lifecycle Management (MLM) and alert settings.
Offers best practices for effectively using MLM and ensuring data protection through strategy and policy development.
Details how to generate reports about media health, remaining capacity, and other lifecycle data in the library.
Explains the BlueScale Encryption system, its components, and the differences between Standard and Professional Editions.
Guides users on deciding whether to encrypt all data or a subset, and how to group encrypted data.
Details the critical tasks of exporting and protecting encryption keys for data decryption and recovery.
Describes how to decrypt and restore data when the encryption key is stored within the library.
Provides steps to import an encryption key from a USB storage device into the library.
Outlines the procedure for deleting an encryption key from the library, emphasizing the need for backups.
Explains how to view library messages to diagnose problems and follow recommended steps for resolution.
Shows how to view the current BlueScale Hardware Health Monitoring (HHM) data for the library.
Explains how to save trace results to a USB device for later analysis or submission.
Details restoring library configuration and MLM database using the auto-save backup file.
Describes how to restore library configuration from a saved file or upload.
Provides steps to restore the MLM database from a previously saved backup file.
Explains how to view the current status of each tape drive in the library via the Drive Details screen.
Offers general tips for troubleshooting tape drive problems, including checking write-protect switches and cleaning.
Covers procedures for updating the library and its components with the latest firmware packages.
Details Spectra Logic's support model for firmware packages and customer upgrade recommendations.
Explains how to set up local servers to store firmware packages for updating multiple Spectra libraries.
Provides instructions on how to delete firmware package files from local storage on the LCM.
Describes cartridges and accessories available for purchase for the Spectra T50e library.
Details library system and hardware upgrades available for purchase, including capacity and software options.
Describes the library's accommodation of tape drives, including types and installation.
Explains the library's power supply requirements and the option for N+1 redundancy.
Details the Library Controller Module (LCM) and its function in library operation.
Provides information on SpectraGuard Technical Support services, including on-site maintenance and repair.
Outlines the procedure for returning library components for service, including shipping instructions.
Describes the standard Next Business Day On-Site service included with the library warranty.
Outlines the library specifications, including data storage capacity, size, weight, and power requirements.
Details the flexible storage capacity of the T50e library, from 10 to 50 slots, and maximum compressed capacity.
Provides input power requirements, power cord specifications, and power consumption/cooling requirements for the library.
Lists the general environmental specifications for the library's operating environment, including temperature and humidity.
Describes the interfaces and cables supported by the library for connecting tape drives to the host.
Provides specifications for LTO-4 tape drives, including transfer rate, encryption, and power consumption.
Details the different generations of LTO Ultrium data cartridges, including capacity and color.
Lists the domestic and international product safety standards the Spectra T50e Library complies with.
Provides information regarding the Spectra T50e Library's compliance with FCC rules for Class A digital devices.
Emphasizes the importance of backing up library metadata, including configuration and encryption keys.
Describes best practices for using LTO media and managing the media inventory.
Provides definitions for terms starting with 'A' relevant to the Spectra T50e library.
Provides definitions for terms starting with 'D' relevant to the Spectra T50e library.
Provides definitions for terms starting with 'H' relevant to the Spectra T50e library.
To Next Page
