EasyManua.ls Logo

Spectra Precison HL450 User Manual

Spectra Precison HL450
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
www.spectraprecision.com
1. Keypad - Power, Accuracy, Units & Volume switches.
2. Beeper output - Fast, solid & slow audible signal.
3. Bubble Vial - aids in keeping HL450 level.
4. Anti-strobe sensor - Reduces false indication from
strobe lights.
5. SuperCell Reception Window - 4.0 in / 102 mm of
height.
6. Front LCD - Displays elevation, settings and status.
7. On-grade Mark - Aligned with laser center on-grade
reading.
8. Battery Door & Latch for two “AA” batteries.
9. Marking Notch (3.15 in / 80.0 mm from top).
10. Captive Screw Thread
11. Clamp Guides - Dimples align rod clamp.
12. Serial Number / ID Label.
13. Rear LCD - repeats indications of front LCD.
Front view
Rear view
Working Radius: 1 m - 400 m (3 ft - 1300 ft)
(Laser dependent):
Laser Detection Height: 102 mm (4“)
Numeric Readout Height: 76 mm (3“)
Accuracy (Dead band):
Fine 1.0 mm 0.05 in 1/16 in
Medium 5.0 mm 0.20 in 1/4 in
Calibration 0.1 mm 0.01 in 1/64 in
Reception Angle: ± 45° minimum
Detectable Spectrum: 610 nm ... 900 nm
Beeper Volumes: Loud = 100+ dBA
Low = 65 dBA
Power Supply: 2 x 1.5 Volt “AA” batteries
Battery Life: 70+ hours
Automatic Shut Off: 30 min
Environmental: Waterproof, Dustproof to IP67
Weight without clamp: 371 g (13.1 oz.)
Dimensions without clamp:
168.0 x 76.0 x 36.0 mm
(6.6” x 3.0” x 1.4”)
Operating Temperature: -20°C...+60°C (-4°F...+140°F)
Storage Temperature: -40°C...+70°C (-40°F...+158°F)
*Specifications subject to change without notice.
Precisional Operaons LLC warrants the HL450 to be free of
defects in material and workmanship for a period of three
years. Precisional Operaons LLC or its authorized service
center will repair or replace, at its opon, any defecve part,
or the enre product, for which noce has been given during
the warranty period. If required, travel and per diem expenses
to and from the place where repairs are made will be charged
to the customer at the prevailing rates. Customers should
send the product to Precisional Operaons LLC or the nearest
authorized service center for warranty repairs or exchange,
freight prepaid. Any evidence of negligent, abnormal use,
accident, or any aempt to repair the product by other than
factory-authorized personnel using Precisional Operaons
LLC cered or recommended parts, automacally voids the
warranty. The foregoing states the enre liability of Precisional
Operaons LLC regarding the purchase and use of its equipment.
Precisional Operaons LLC will not be held responsible for any
consequenal loss or damage of any kind. This warranty is in
lieu of all other warranes, except as set forth above, including
any implied warranty merchantability of tness for a parcular
purpose, are hereby disclaimed. This warranty is in lieu of all
other warranes, expressed or implied.
© 2022, Precisional Operaons LLC. All rights reserved.
Reorder PN 1277-3965B (09/22)
Specicaons Warranty
8
9
10
11
12
13
3
5
6
4
1
2
7
EMC Declaraon of Conformity
This receiver has been tested and found to comply with the lim-
its for a Class B digital device for radio noise for digital apparatus
set out in the Radio Interference Regulaons of the Canadian
Department of Communicaon, and is pursuant to part 15 of
the Federal Communicaon Commission (FCC) rules. These lim-
its are designed to provide reasonable protecon against harm-
ful interference in a residenal installaon. This receiver gen-
erates radio frequency. If its not used in accordance with the
instrucons, it may cause harmful interference to radio or tele-
vision recepon. Such interference can be determined by turn-
ing the receiver o and on. You are encouraged to try eliminat-
ing the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the laser and the receiver.
For more informaon, consult your dealer or an experience
radio/television technician.
CAUTION: Changes or modicaons to the receiver that are not
expressly approved by Precisional Operaons LLC could void
authority to use the equipment.
Declaraon of Conformity
Applicaon of Council Direcve(s): 89/336/EEC
Manufacturer’s Name: Precisional Operaons LLC
Manufacturer’s Address: 3265 Logiscs Lane
Vandalia, Ohio 45377 U.S.A.
European Representave Address:
Spectra Precision (Kaiserslautern) GmbH
Am Sportplatz 5
67661 Kaiserslautern, Germany
Model Number: HL450
Conformance to Direcve(s): EC Direcve 89/336/EEC using
EN55022 and EN50082-1
Equipment Type/Environment: ITE/residenal, commercial
& light industrial
Product Standards: Product meets the limit B and
methods of EN55022
Product meets the levels and
methods of IEC 801-2, 8 kV air,
4 kV contact IEC 801-3, 3 V/m
26 to 1000 MHz 80%, @ 1 kHz
HL450
Digital Readout Receiver
User Guide
Precisional Operaons LLC
3265 Logiscs Lane
Vandalia, Ohio 45377 U.S.A.
Telephone: +1-888-527-3771
Spectra Precision (Kaiserslautern) GmbH
Am Sportplatz 5
67661 Kaiserslautern, Germany
Telephone: +49-6301-32213
www.spectraprecision.com
Noce to Our European Union Customers
For product recycling instrucons and more informaon, please go to:
https://www.trimble.com/en/our-commitment/responsible-business/product-
compliance/environmental-compliance
Instrucons for Return to ERFC:
•WEEE is to be shipped to the ERFC, clearly stang WEEE on the delivery note and / or packaging
•Specic product number and serial number informaon is not required
•Addional return authorisaon from Trimble Support is not required
•Delivery Address:
Trimble Europe B.V.
Industrieweg 187A
5683 CC, Best
The Netherlands
N324
Question and Answer IconNeed help?

Do you have a question about the Spectra Precison HL450 and is the answer not in the manual?

Spectra Precison HL450 Specifications

General IconGeneral
BrandSpectra Precison
ModelHL450
CategoryReceiver
LanguageEnglish

Summary

Warranty

Warranty Details

Precisional Operations LLC warrants the HL450 to be free of defects in material and workmanship for three years.

EMC Declaration of Conformity

Declaration of Conformity

Details the product's conformance to EU directives and relevant product standards for electromagnetic compatibility.

Installing the Batteries

Battery Status

Indicates the current charge level of the inserted batteries for the device.

Rod Clamp

Details the components and function of the rod clamp used for securing the detector.

Receiver Operation

Power ON/OFF

Instructions on how to power the digital readout receiver on and off using the dedicated button.

Select Accuracy

Guide on how to change the deadband (accuracy) setting of the receiver.

Select Beeper Volume

Procedure for adjusting the audible signal volume from the receiver unit.

Select Units of Measure

Steps to change the displayed units of measurement for the receiver.