Spectrum Brands Kwikset Home Connect 620 User Manual

1 / 4
03809* (2x)
(For Latch/
Strike Bag)
If drilling a new door, use the supplied template and the complete
door drilling instructions available at kwikset.com/doorprep
13/8" –2"
35 – 51 mm
A B
C
D
Extend the latch bolt.
Is the D-shaped hole centered in the door hole?
Install the latch.Hold the latch in front of the door hole, with the latch
face lush against the door edge.
1"
25 mm
YES NO
No adjustment is required.
Proceed to next step.
D-shaped hole D-shaped hole
Rotate latch face as
shown to extend latch.
UP is on top.
E
Install the strike on the door frame.
Make sure the hole in the door frame is drilled
a minimum of 1" (25 mm) deep.
1
2
Prepare the door and check dimensions
Install the latch and strike
or
23/8" or 23/4"
60 or 70 mm
backset
Measure to conirm that the backset is
either 23/8" or 23/4" (60 or 70 mm).
Measure to conirm that the hole
in the door edge is 1" (25 mm).
Measure to conirm that the door is between
13/8" and 2" (35 mm and 51 mm) thick.
Remove your existing deadbolt
from your door.
C D E F
B
Latch A
“B” is not included.
If needed, please contact
Kwikset to order a drive-in
latch for your lock.
Keys
Exterior Assembly
Adapter
Ring
Batteries
Mounting
Plate
Parts List
For Latch / Strike
Interior Assembly
SmartKey
Tool
Measure to conirm that the hole in the door is either
21/8" (54 mm) or 11/2" (38 mm).
or
21/8"
54 mm
11/2"
38 mm
Note: Additional door
preparation may be
required for doors with
11/2" (38 mm) holes.
Consult the deadbolt
drilling instructions at
kwikset.com/doorprep
A
Make sure your door is compatible. If you have a standard deadbolt mounted
separately from the handle below it, your door is compatible.
Mortise
Lock
Not CompatibleNot Compatible
Rim
Lock
Compatible Not Compatible
Integrated
Interior
door frame
46780* (4x)
(For Latch/
Strike Bag)
*Install the longer screws
closest to the door jamb.
actual size
Strike
03809
46780
68272
69316
Latch B
For Lock
03809
46780
or
or
*Use longer screws if
holes are worn out.
You will have two extra screws.
actual size
For Latch /
Strike Bag
(2x) (2x)
(2x) (2x)
6
9369003
Rev 04
ZWave Plus™
Installation and User Guide
Kwikset
1-866-863-6584
www.kwikset.com
ENGLISH
Required tools
Ruler
Phillips head screwdriver

Spectrum Brands Kwikset Home Connect 620 Specifications

General

Brand	Spectrum Brands
Model	Kwikset Home Connect 620
Category	Door locks
Language	English

Summary

Prepare the Door and Check Dimensions

Check Door Hole Diameter

Measure to confirm the door hole is either 2-1/8" (54 mm) or 1-1/2" (38 mm).

Check Backset Measurement

Measure to confirm the backset is either 2-3/8" or 2-3/4" (60 or 70 mm).

Check Door Edge Hole

Measure to confirm the hole in the door edge is 1" (25 mm).

Check Door Thickness

Measure to confirm the door is between 1-3/8" and 2" (35 mm and 51 mm) thick.

Install Latch and Strike

Extend Latch Bolt

Extend the latch bolt prior to installation.

Position Latch

Hold the latch flush against the door edge.

Center D-Shaped Hole

Verify if the D-shaped hole is centered in the door hole.

Install Latch

Install the latch into the door.

Install Strike

Install the strike on the door frame.

Install Exterior Keypad

Check Door Hole Diameter

Verify door hole diameter (2-1/8" or 1-1/2") and install adapter ring if needed.

Prepare Mounting Plate

Remove the interior assembly's mounting plate.

Install Exterior Assembly

Install the exterior keypad and mounting plate, routing the cable.

Install Interior Assembly

Prepare Interior Assembly

Orient the turnpiece shaft upwards and remove interior cover.

Attach Interior Assembly

Install the interior assembly onto the mounting plate, ensuring cable connection.

Install Batteries and Perform Door Handing

Install Batteries

Install 4 AA batteries into the battery pack.

Initiate Auto-Handing

Install the battery pack with the door open to start auto-handing.

Status LED Feedback

Observe the Status LED for success (Green) or failure (Red) of door handing.

Add Lock to Smart Home System

Initiate Pairing

Start the pairing process with your smart home controller.

Enter Add Mode

Press button 'A' on the lock interior to enter Add Mode.

Enter PIN

Enter the 5-digit PIN if prompted by the smart home system.

Troubleshooting Pairing

Follow instructions for renaming or re-pairing if unsuccessful.

Add User Codes

Initiate Programming

Press the "Program" button once with the door open.

Enter User Code

Enter a user code (4-8 digits) and press the lock button.

Programming Feedback

Check for Green light/one beep (success) or Red light/three beeps (failure).

Test Lock and Door Alignment

Test Latch Extension

Insert key to extend latch, ensuring smooth operation.

Test Latch Retraction

Turn key 180° to retract latch, ensuring smooth operation.

Test Locking

Close door, insert and rotate key to lock, ensuring smooth operation.

Test Unlocking

Turn key 180° to unlock, ensuring smooth operation.

Install Interior Cover

Install Cover

Place the interior cover and align the turn piece shaft.

Install Screws

Secure the interior cover with screws.

System Alerts and Troubleshooting

System Alerts Overview

Details on alerts, reasons, and solutions for lock behavior.

Status LED Indicators

Explains Status LED behavior for various lock states.

Mute/Unmute Audio

Instructions on how to mute or unmute lock audio.

Auto-Lock Function

Details on configuring the auto-lock timer.

Advanced Operations and Maintenance

Factory Reset

Procedure to reset the lock to factory default settings.

SmartKey Re-Keying

Instructions for re-keying the SmartKey lock.

Network Information

Details on removing the lock from the Z-Wave network.