WALL PACK SERIES
SEMI CUT-OFF WALL PACK LUMINAIRE
INSTALLATION MANUAL
SAFETY INFORMATION
BE SURE THE POWER IS OFF! RISK OF ELECTRICAL SHOCK: Always use the switch to power off. Do not perform
any operations while this unit is powered on. The electrical system you want to connect the device to must be
grounded. Read the instructions before using or powering this device. The safety instructions must remain with
the unit in case of transfer. Any damage to the device linked to an inappropriate use is excluded from support by
the warranty. Before connecting, make sure that the current and voltage are compatible with this device. We highly
recommend that all installations are made by QUALIFIED ELECTRICIAN. We are NOT responsible by any means for
the use or misuse of the following information. We are NOT responsible in whole or part for any harm or damage
that may or may not be caused. We reserve the right to revise the components of any product, due to part availability
or change ETL, CUL, UL standards without assuming any obligation or liability to modify any products previously
manufactured and without notice. These instructions do not cover all details of variations in equipment, nor do they
provide every possible contingency to be met. Turn off / unplug power when installing or service device.
WARNING: Read all safety precautions and installation instructions carefully before installing or servicing this
xture. Failure to comply with these instructions could result in a potentially fatal electric shock, re, and/or
property damage.
• To prevent injury or product damage only licensed electricians should install
• To avoid electric shock or component damage disconnect power before attempting installation or servicing
• This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state
and local electric codes and safety
• Disconnect product and allow cooling prior to servicing
• Any alteration or modification and/or electrical shock this product must be properly grounded
• To prevent product malfunction and/or electrical shock this product must be properly grounded
• Do not use the lamp in an area where there is heavy aggressive gas
• Do not cover anything on the lamp which is harmful for heat sink
• Products faults caused by separating, remodeling or incorrect construction are not in the quality warranty range
WARNING
FCC WARNING
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance
could void the user authority to operate the equipment.
NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
PRE - INSTALLATION
•Carefully remove the fixture from the carton.
•Before beginning assembly, installation, or operation of product, make sure all parts
are present. Compare parts with package contents list and diagram on previous
page. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement parts.
• Tools required for assembly (Not Included): screwdriver, phillips screwdriver, pliers,
electrical tape, wire cutters, safety glasses, ladder, wire stripper.
PRODUCT PARAMETER
INPUT VOLTAGE 100-277V
WATTAGE 60W, 80W, 100W, 120W
FEATURE IP65 RATING
www.spitzerlighting.com
702 Interchange Blvd., Newark, DE 19711 Specication is subject to change without notice
1/2
CARE AND MAINTENANCE
CAUTION: Before attempting to clean the xture, disconnect the power to the xture
by turning the breaker off or removing the fuse from the fuse box. This LED light
xture is made from quality materials that will last many years with minimum care
and maintenance. You may want to clean the xture with a soft cloth periodically.
To maintain the best appearance of the xture, do not use cleaners with chemicals,
solvents or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or
wiring inside the light xture.
TROUBLE SHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Light will not come on A. Fixture not properly connected
B. Fixture not receiving power.
A. Check wires to ensure proper connections.
B. Check to make sure breaker is on and test
another working electrical device to make sure it
is receiving power.
HARDWARE
ASSEMBLY INSTRUCTIONS
SAFETY INFORMATION
PRE-INSTALLATION
Please read and understand this entire manual before
attempting to assemble, operate or install the product.
WARNING
● Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse
or switching off circuit breaker.
● Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not allow wires
to contact any surface having a sharp edge. By doing so, it may damage or cut the wire insulation, which
could cause serious injury or death from electric shock.
● LED electronics can be damaged by electrostatic discharge (ESD) shock. Before installation, discharge
yourself by touching a grounded bare metal surface to remove this hazard. To avoid unintended damage,
do not touch the LED module.
CAUTION
● All electrical connections must be in accordance with local codes, ordinances or the national electric code (NEC).
● Contact your municipal building department to learn about your local codes, permits and/or inspections.
● Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60°C.Consult a qualified
electrician before installation.
● Do not connect this fixture to an electrical system that does not provide a means for equipment grounding or
a ground wire. Never use this fixture in a two-wire system that can not be grounded. If you are not sure your
electrical system has a ground wire, do not attempt to install this fixture. Contact a qualified, licensed
electrician for information with regards to proper grounding methods as required by the local electrical code
in your area.
● If a dimmer switch is used with this fixture, obtain professional advice to determine the correct type and
electrical rating required.
● Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts
with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
● Tools required for assembly (not included): Flat-head screwdriver, phillips screwdriver, pliers, electrical tape,
wire cutters, safety glasses, ladder, wire stripper.
● Non-replaceable LEDs.
● If you are not familiar with state and local electrical codes, it is recommended that you consult with a
qualified electrician.
Suitable for use in wet locations.●
Caution: LEDs emit bright light. Avoid looking directly into the light source for prolonged periods to avoid
eye damage.
INSTALLATION
●
AA: Wire Nuts (3)
BB: Gasket (1)
CC: Machine Screws (2)
A
B
C
D
D
E
AA
BB
CC
C
E
Junction Box
CAUTION:
1.DO NOT OVERSPREAD THE PHOTOCELL
CONTROLLER (PART D).
2.ENSURE THE WATERPROOF RUBBER GASKET
(PART F) IS ASSEMBLED IN PLACE. (FIGURE 4)
F
C
WARNING: Turn off the power at fuse or circuit box.
1. Loosen 2 pcs set screws (Part B) and open the upper cover plate of the fixture (Part A) slowly. (Figure 1)
2. Drill 2 holes on the pedestal of the fixture (Part C). (Figure 1)
3. Thread Machine Screws (Part CC) to tighten the pedestal of the fixture (Part C) with the Gasket (Part BB). (Figure 1)
4. Make wire connections in accordance with local codes by using the Wire Nuts (Part AA) to secure
wiring connection. (Figure 1)
● Connect the HOT wire (black) from the main source to the BLACK wire from the power supply (Part E).
● Connect the NEUTRAL wire (white) from the main source to the WHITE wire from the power supply (Part E).
● Connect the GROUND wire (green/yellow) from the main source to GROUND wire (green/yellow)
from the power supply (Part E).
5. Close the upper cover plate of the fixture (Part A) slowly and tighten 2 pcs set screws (Part B). (Figure 1)
6. Turn on the power at fuse or circuit box.
(Figure 1)
(Figure 2)
(Figure 3)
● turn on/off the fixture by detecting ambient light use the photoreceptor (optional).
● Multivolt (100~277V (default)) or 347V (optional) for commercial or residential use.
To Next Page
General