Spotlight Sintesi AR 05

To Next Page

I - DESCRIPTION OF THE PROJECTOR

II - GENERAL

III - INSTALLATION

WARNING!

ALWAYS

CONNECT THE

PROJECTOR TO A

MAIN WHICH IS

PROTECTED BY A

SUITABLE

ELECTRIC FUSE

SELECTED

ACCORDING TO

THE

INSTRUCTIONS

1.Suspension clamp

2. Accessory guides with retaining clip

3. Spring-loaded latch lock

4. Lever handle for adjusting projector inclination

5. Lamp holder tray access knob

6. Retaining spring for lamp holder pan

7. Hook for anchorage of safety chain

8. Lamp position adjustment knob

9. Wing nut for locking and adjusting projector focus

The projector you have bought satisfies directives 73/23/EEC

as it complies with standards EN 60598-1 and EN 60598-2-17.

! model

! maximum supply voltage in V

! maximum power of the projector in W

! the index of protection IP

! maximum temperature of the environment admitted in °C

! maximum temperature of the projector body in °C

! minimum distance from any inflammable surface

! information to find the position 0 of the projector: when

the tip of the arrow points upwards

! maximum angle of inclination upwards and downwards.

These limits, imposed by the lamp manufacturer,

should not be exceeded as they would reduce the

projector’s useful life or lead to its deterioration.

The projector can be either suspended or mounted on a stand.

WARNING!

DO NOT INSTALL THE PROJECTOR ON SURFACES WHICH

ARE USUALLY INFLAMMABLE.

The minimum distance at which the projector must be kept from

easily inflammable surfaces is indicated on the label.

The safety norms estimate that a metal wire screen be mounted

on the front of the projector to prevent any large glass fragments

from falling if the projector breaks.

WARNING!

REPLACE THE LAMP AND/OR LENS IF VISIBLY DAMAGED.

For safety reasons always use the safety chain between the

projector and the suspension truss.

3.1 - Accessories

The accessories estimated for this projector are listed in the

price list and can be mounted by inserting into guides 2.

3.1.1. - Colour changer

Insert the flange of the colour changer into its guide so that the

latch remains closed and the retaining spring is released.

Connect the safety cable to the special hook of the projector.

3.1.2. - Lens flaps

Mount them in the same way as the colour changer.

Sintesi Line

Mod.AR 05- Ar12 -AR 25

Mod.VA 05- Va12 - VA 25

Other manuals for Spotlight Sintesi AR 05

User Manual12 pages

Need help?

Do you have a question about the Spotlight Sintesi AR 05 and is the answer not in the manual?

The Spotlight projector, available in AR and VA models (05, 12, 25), is a lighting device designed for various applications, offering both suspension and stand-mounted installation options. It complies with directives 73/23/EEC and standards EN 60598-1 and EN 60598-2-17, ensuring safety and performance.

Function Description

The projector's primary function is to provide adjustable illumination. It features a robust design with several components that allow for precise control over light direction and focus. Key elements include a suspension clamp for mounting, accessory guides with a retaining clip for attaching additional components, and a spring-loaded latch lock for secure operation.

Adjustments to the projector's inclination are made via a lever handle, while a wing nut allows for locking and fine-tuning the focus. The lamp holder tray, accessible through a dedicated knob, facilitates lamp changes. A retaining spring secures the lamp holder pan, and a hook is provided for anchoring a safety chain, an essential feature for secure installation. The lamp position can be adjusted using a specific knob, further enhancing control over the light beam.

The projector is designed to be versatile, allowing users to modify the light beam's width by shifting the lamp carriage forward or backward. This adjustment is crucial for adapting the projector's output to different lighting requirements, from narrow, focused beams to wider illumination.

Usage Features

Installation of the Spotlight projector is flexible, supporting both suspension and stand mounting. Users are cautioned against installing the projector on easily inflammable surfaces, and a minimum distance from such surfaces is indicated on the device label. For enhanced safety, a metal wire screen is recommended on the front of the projector to contain any glass fragments in case of lamp breakage.

The projector is designed for ease of use, with intuitive controls for adjusting its position and focus. The side handle allows users to loosen the projector, change its inclination, and then lock it back into position. Similarly, the projector can be rotated on its vertical axis by loosening the wing nut. The lamp position adjustment knob enables users to fine-tune the lamp's placement, which in turn controls the beam's spread.

Accessories, such as colour changers and lens flaps, can be easily integrated into the projector. These accessories are mounted by inserting their flanges into the designated guides, ensuring a secure fit with the latch remaining closed and the retaining spring released. For safety, accessory cables should be connected to the projector's special hook.

Lamp replacement is a straightforward process, though safety precautions are paramount. Users must disconnect the projector from the mains before opening the lamp holder tray. The lamp is inserted into the socket, with care taken not to touch the glass. The design ensures that changing the lamp does not necessitate re-adjusting the lamp carriage or the projector's optical settings, maintaining consistent performance. However, when upgrading to a higher wattage lamp (e.g., from 1000W to 1200W), the lamp holder pan must be shifted from a high to a low position, and the retaining spring repositioned accordingly.

Electrical connections are designed for safety, with the projector operating at a maximum voltage of 240V. The power cable adheres to CEI 20-35 standards, and it is critical to ensure that the ground connection is always established.

Maintenance Features

To ensure optimal performance and longevity, the Spotlight projector requires regular maintenance. Both the lens and the reflector should be kept clean. Cleaning involves disconnecting the projector from the mains, opening it, and gently wiping the lens and reflector with a soft cloth dampened with alcohol. This routine cleaning prevents dust and grime buildup, which can degrade light output and quality.

Beyond routine cleaning, an annual service check is recommended. This involves inspecting the integrity of all electrical and mechanical components. Regular professional maintenance helps identify and address potential issues before they lead to malfunctions, ensuring the projector remains safe and efficient. Users are also advised to replace any visibly damaged lamps or lenses immediately for safety reasons. The safety chain between the projector and the suspension truss should always be in place and regularly checked for integrity.