Stagg 15 GA DR User Manual

BACK PANEL:
WARNING: This amplier must be earthed. Please check that the supply voltage details given on the
rating label (located on the rear panel) are in accordance with your electricity supply.
1 POWER FUSE: In the event of the power fuse having to be replaced, rst unplug the power cable
from the mains outlet. Then remove the fuse cover and replace the power fuse with one of the same type
and value. Never plug the power cable back into the mains outlet without the fuse cover. When powering
on the amplier, if the power fuse blows up again, go to a suitable service centre for repair.
MAINS CABLE: This amplier features a power cable with a moulded-on plug. If the socket outlets in the
home are not suitable for the plug supplied with this amplier, use an appropriate plug adapter that can
handle the power required for this amplier. In case the power cable or plug is damaged, unplug it in a
safe way from the mains outlet and go to a suitable service centre for replacement.
Features and Specications are subject to change without notice.
FRONT PANEL:
1. INPUT: Plug your guitar in here. We recommend that you always use a high-quality shielded guitar
cable to prevent any background noise interference or unwanted feedback.
2. (Overdrive) GAIN: This control determines the distortion intensity of the amplier’s overdrive setting.
Adding GAIN will make your guitar sound more distorted.
3. (Overdrive) SWITCH: This switch activates the amplier’s built-in overdrive function, which adds
distortion to the signal.
4. (Clean) VOLUME: This control determines the amplier’s overall output volume.
5. TREBLE: This control determines the level of high frequencies in the output signal. Adding TREBLE will
make your guitar sound brighter and sharper.
6. MID: This PARAMETRIC control determines the level of middle frequencies in the output signal. Adding
MID will make your guitar sound rounder and fuller.
7. BASS: This control determines the level of low frequencies in the output signal. Adding BASS will make
your guitar sound warmer and heavier.
8. DIGITAL REVERB: This is the reverb intensity control. This controls the amount of reverb that is added
back to the original dry signal. Adding DIGITAL REVERB will produce a reverberation effect in your guitar
sound, as though you were playing in a large hall. A little can go a long way in adding that special depth to
your sound. If engaged, the reverb is always active in either overdrive or clean mode.
9. CD/MP3 INPUT: This is a line level 1/4” (Ø 6.3 mm) stereo jack into which an MP3/CD/Tape player
may be connected.
10. PHONES: This is a 1/4” (Ø 6.3 mm) standard jack output to connect the headphones. When
headphones are connected, no sound is produced from the speaker.
11. POWER LED: When this red LED is lit, the amplier is ready to work. When it is off, it means the
amplier is powered off.
12. POWER: This switch turns the amplier on or off.
2 3
USER’S MANUALSUSER’S MANUAL 15 GA DR 15 GA DR
1
1 2 3 4 5 6 7 8 12109 11
TECHNICAL SPECIFICATIONS
Max. Rated Power / Loudspeaker 15 Watts RMS @ 8 Ohms load / 6.5” speaker
Frequency Response 80 Hz to 15 kHz
Total Harmonic Distortion 0.8% (Clean Mode)
Signal to Noise Ratio - 55 dB @ max Rated Power
Input Impedance
220k Ohms
Power Consumption
20 Watts max
Maximum Input Level
45 mV (RMS)
Maximum Gain
42 dB (@ 1kHz)
Dimensions (H x W x D)
31 x 35 x 19 cm / 12.2 x 13.8 x 7.5 in.
Weight
6.3 kg / 13.9 lbs

Stagg 15 GA DR Specifications

General

Brand	Stagg
Model	15 GA DR
Category	Amplifier
Language	English