EasyManua.ls Logo

STARTRITE 403 - User Manual

STARTRITE 403
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
403 16" Trade Bandsaw
503 20" Trade Bandsaw
603 24" Trade Bandsaw
Original Instruction Manual
Important
For your safety read instructions carefully before
assembling or using this product.
Save this manual for future reference.
Always wear safety glasses when
using woodworking equipment.
Always read the instructions
provided before using
woodworking equipment.
i
Kg
Version 3.4
December 2017

Table of Contents

Questions and Answers

  • D
    David OlsonAug 9, 2025
    What to do if my STARTRITE 403 stops unexpectedly?
    • K
      Kenneth NewtonAug 9, 2025
      If your STARTRITE bandsaw stops unexpectedly or won't start, there are several potential causes. First, check the plug connection to ensure the bandsaw is properly plugged in. If the plug is connected, inspect the fuse or circuit breaker and replace the fuse or reset the circuit breaker if necessary. A damaged power cord can also cause this issue, so examine the cord and replace it if it is damaged.
  • C
    Catherine MorenoAug 14, 2025
    Why does the blade wander when cutting with my STARTRITE Saw?
    • M
      Melissa LloydAug 14, 2025
      If the blade wanders during cutting with your STARTRITE Saw, several factors could be the cause. Make sure the fence is aligned with the table, and adjust if necessary. Warped timber can also cause the blade to wander, so try using alternative timber. An excessive feed rate could be the reason, so reduce the feed rate. Ensure that you are using the correct type of blade and the blade tension is set according to the blade type. Finally, check and adjust the blade guides.
  • E
    Elizabeth ThompsonAug 19, 2025
    How to improve the cut quality of my STARTRITE 403 Saw?
    • A
      Ashley FloresAug 19, 2025
      If your STARTRITE Saw provides an unsatisfactory quality of cut, consider these points: the blade may be dull and needs replacing. Also, make sure the blade is mounted correctly with the teeth pointing downwards. Gum or pitch on the blade or table can also affect the cut quality, so remove and clean the blade and the table. Finally, ensure you are using the correct type of blade for the cut.
  • J
    Jane DavisAug 25, 2025
    How to make accurate cuts with my STARTRITE 403?
    • T
      Tammy EvansAug 25, 2025
      If you cannot make accurate 90º or 45º cuts with your STARTRITE Saw, the table stop may not be set correctly. Check that the blade is at 90º to the table with a try square and adjust the stop if needed. Also, the angle pointer might not be set accurately; check the blade as described above and set the pointer correctly. Ensure the mitre gauge is in the correct position.
  • T
    Teresa ReedAug 29, 2025
    What to do if my STARTRITE 403 vibrates too much?
    • K
      Kelsey JohnsonAug 29, 2025
      If your STARTRITE bandsaw vibrates excessively, there are several things you can check. Ensure the bandsaw is placed on a level surface. A worn-out V-belt can cause vibrations, so replace it if necessary. Also, check if the motor mount is loose and tighten the motor mounting hardware. Finally, inspect for any loose hardware and tighten it.
  • A
    Adam ReedSep 3, 2025
    Why doesn't my STARTRITE 403 blade come up to speed?
    • J
      Jonathan LawrenceSep 3, 2025
      If the blade on your STARTRITE Saw does not come up to speed, the extension cord might be too long or lightweight; replace it with a cord of adequate size and length. Alternatively, there may be low workshop voltage, in which case you should consult a qualified electrician.

STARTRITE 403 Specifications

General IconGeneral
BrandSTARTRITE
Model403
CategorySaw
LanguageEnglish

Related product manuals