- 13 -
Functional warranty
This STEINEL product has been manufactured with
utmost care, tested for proper operation and safety
and then subjected to random sample inspection.
STEINEL guarantees that it is in perfect condition
and proper working order.
The warranty period is 36 months and starts on the
date of sale to the consumer. We will remedy defects
caused by material flaws or manufacturing faults.
The warranty will be met by repair or replacement of
defective parts at our own discretion. The warranty
shall not cover damage to wear parts, damage or
defects caused by improper treatment or mainten-
ance. Further consequential damage to other objects
is excluded.
Claims under the warranty will only be accepted if the
unit is sent fully assembled and well-packed with a
brief description of the fault, a receipt or invoice (date
of purchase and dealer's stamp) to the appropriate
Service Centre.
Repair service:
Our Customer Service Department
will repair faults not covered by war-
ranty or after the warranty period.
Please send the product well packed
to your nearest Service Centre.
Declaration of conformity
This product complies with Low Voltage Directive
06/95/EC, EMC Directive 04/108/EC as well as
RoHS Directive 02/95/EC.
Troubleshooting
Sensor-switched LED floodlight
without power
Sensor-switched LED floodlight
will not switch "ON"
Sensor-switched LED floodlight
will not switch "OFF"
Sensor-switched LED floodlight
switches "ON" when it should not
Malfunction
■ Fuse faulty, not switched "ON",
break in wiring
■ Short circuit
■ Fit new fuse; switch "ON"
mains switch; Check wiring
with voltage tester
■ Check connections
■ Twilight control set to night-time
mode during daytime operation
■ Mains power switch "OFF"
■ Fuse faulty
■ Detection zone not properly
targeted
■ Adjust setting
■ Switch "ON"
■ Fit new fuse, check connection
if necessary
■ Re-adjust
■ Continuous movement in the
detection zone
■ Check zone and readjust if
necessary or apply shroud
■ Wind is moving trees and
bushes in the detection zone
■ Cars in the street are being
detected
■ Sudden temperature changes
due to weather (wind, rain,
snow) or air expelled from fans,
open windows
■ Sensor-switched LED floodlight
is moving (swaying) due to gusts
of wind or heavy rain.
■ Change detection zone
■ Change detection zone
■ Adjust detection zone or install
in a different place
■ Mount sensor-switched LED
floodlight on a firm surface
Cause Remedy
Sensor-switched LED floodlight
keeps switching "ON" and "OFF"
■ Animals moving in the
detection zone
■ Tilt sensor higher or apply
specific shrouds; adjust zone,
or apply shrouds
- 12 -
Operation and maintenance
The unit is not suitable for special burglary alarm
systems since it lacks the tampering protection pre-
scribed for this purpose. Weather can affect operation
of the sensor-switched LED floodlight. Strong gusts
of wind, snow, rain and hail may cause the light to
come on when it is not wanted because the sensor is
unable to distinguish sudden changes in temperature
from sources of heat.
The detector lens may be cleaned with a damp cloth
if it gets dirty (do not use cleaning agents).
Accessories
Ground spike, silver, 365 x 136 x 80 mm
Article no. 654917
Permanent light function
If a mains switch is installed in the mains supply lead,
the light is capable of the following functions in addi-
tion to the simple "ON"/"OFF" function:
Sensor operation
1) Switch light "ON" (when floodlight is "OFF"):
Switch "OFF" and "ON" once.
LEDs stay "ON" for the period selected.
2) Switch light "OFF" (when floodlight is "ON"):
Switch "OFF" and "ON" once.
Floodlight goes out or switches to sensor mode.
Manual override
1) Activate manual override:
Turn switch "OFF" and "ON" once. The floodlight is
set to stay on for 4 hours (red LED lights up behind
the lens). Then it returns automatically to sensor
mode (red LED off).
2) Deactivate manual override:
Switch "OFF" and "ON" once. Floodlight goes out or
switches to sensor mode.
Important:
The switch should be actuated in rapid succession
(in the 0.5 – 1 sec. range).
Technical specifications
Sensor-switched LED floodlight XLed 10 XLed 25
Wattage: 10 LEDs, approx. 25 W 25 LEDs, approx. 60 W
Additional switching capacity: – 800 W max. – 800 W max.
(resistive load, e.g. filament bulb) (resistive load, e.g. filament bulb)
– 400 W max. (uncorrected, – 400 W max. (uncorrected,
inductive, cos ϕ = 0.5, inductive, cos ϕ = 0.5,
e.g. fluorescent lamps) e.g. fluorescent lamps)
– 400 W max. (electronic ballasts, – 400 W max. (electronic ballasts,
capacitive, e,g, low-energy lamps, capacitive, e.g. low-energy lamps,
4 each max.) 4 each max.)
Life of LEDs: up to 50,000 hrs. up to 50,000 hrs.
(for 3 hrs./day approx. 45 years (for 3 hrs./day approx. 45 years
Angle of coverage: 240° with sneak-by guard 240° with sneak-by guard
Projected area 250 cm
2
+ 103.36 cm
2
420 cm
2
+ 103.36 cm
2
Swivelling range of
sensor unit: ± 80° ± 80°
Swivelling range of housing: 200° vertically 200° vertically
270° horizontally 270° horizontally
Time setting: 5 sec. – 15 min. 5 sec. – 15 min.
Twilight setting: 2 – 2000 lux 2 – 2000 lux
Brightness control: 10% basic brightness (approx. 3 W) 10% basic brightness (approx. 3 W)
Permanent light 'ON': 4 hrs., selectable 4 hrs., selectable
Dimensions (h x w x d) 205 x 200 x 220 mm 300 x 200 x 220 mm
Enclosure: IP 54 IP 54
Protection class: I I
GB
X Led_24spr 28.11.2008 14:42 Uhr Seite 13
To Next Page
Loading...
