EasyManua.ls Logo

Steinsvik Orbit-3100 - User Manual

Steinsvik Orbit-3100
46 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Steinsvik AS Rundhaug 25, 5563 Førresfjorden, Norway | +47 52 75 47 00 | post@steinsvik.no | www.steinsvik.no
User manual
Camera System

Table of Contents

Questions and Answers

  • J
    Jay TuckerAug 3, 2025
    What to do if Steinsvik Orbit-3100 Digital Camera winch will not work?
    • R
      Richard HawkinsAug 3, 2025
      If the Steinsvik Digital Camera winch won't work, several factors could be at play. First, check for any growth on the rope and remove it. Next, ensure the winch rope isn't jammed; if it is, try loosening any knots. Inspect the winch cable for breaks or damages, paying attention to the contacts on the cable and in the PSU. Also, confirm that the camera rope is correctly threaded inside the circlip. Finally, a broken fuse could be the culprit, so check the fuse inside the PSU and replace it if necessary, but remember that only authorized personnel should perform this task.
  • E
    Elizabeth LivingstonAug 16, 2025
    Why does Steinsvik Orbit-3100 Digital Camera winch jerk or stop before reaching the bottom?
    • M
      mary14Aug 16, 2025
      If the Steinsvik Digital Camera winch jerks or stops before reaching the bottom, it could be due to a misplaced bottom stop switch. To resolve this, raise the hoop stopper up and down to the stop screw. A 'click' from the switch inside the winch should occur approximately 5 mm from the bottom position. If the hoop must be raised 1 cm or more to hear the click, the bottom stop switch is misplaced. Another potential cause is an error in the motor protection on the circuit board, in which case Steinsvik recommends a service on the winch.

Summary

3 Safety

3.3 Assessment of escape risk

Assesses the risk of fish escape associated with the camera system's use.

4 Technical Description

4.1 Underwater camera

Details the specifications and models of Steinsvik's underwater cameras (Orbit-3000 series).

4.2 Surface camera

Describes the Orbit-200B and Orbit-210 surface cameras and their specifications.

4.3 PSU

Explains the Power Supply Unit (PSU) and its role in powering and controlling cameras.

4.4 Multiwinch

Details the Multiwinch specifications, mounting, and function for camera movement.

4.5 Orbit-bracket for ring

Describes the Orbit-bracket for ring, its attachments, and specifications.

4.6 Orbit-bracket for ring with clamp

Details the Orbit-bracket for ring with clamp, its features and specifications.

4.7 Antenna and mast

Explains the antenna and mast specifications and their role in data transmission.

4.13 Surveillance camera

Describes Steinsvik's surveillance cameras, Orbit-351 and Orbit-310.

4.14 Fibre receiver cabinet

4.15 Orbit-51 X8 for wireless facilities

5 Preparation and Installation

5.1 Antenna

5.2 Orbit Bracket for ring

5.3 Mast;Alu pipe

5.4 PSU;Protection cabinet

5.5 Winch and winch rope

5.6 Rope and strain relief

5.7 Underwater camera

5.8 Surface camera

5.9 Surveillance camera

6 Operating Instructions

6.1 Multiwinch;underwater camera

Instructions for operating the Multiwinch and underwater camera via software or buttons.

6.2 Surveillance camera

Details controlling the surveillance camera using software, PC, or gamepad.

7 Maintenance

7.1 Routine inspection and periodic maintenance

Provides a table outlining routine inspection tasks and their recommended intervals.

7.3 Troubleshooting and correction of errors

Offers solutions for common problems like winch not working or picture issues.

8 Spare Parts

8.1 Underwater camera

8.2 Obrit-200 (411340) and Orbit-210 (430755)

8.3 Multiwinch (100069)

8.4 Orbit-Bracket for ring (405461)

8.5 Orbit-bracket for ring with clamp (V-Clamp) (442778)

8.6 Antenna (411859)

8.7 Strain Relief (420438)

8.8 Orbit-310 (410478)

Steinsvik Orbit-3100 Specifications

General IconGeneral
BrandSteinsvik
ModelOrbit-3100
CategoryDigital Camera
LanguageEnglish

Related product manuals