STIEBEL ELTRON DHB-E 11 SLi electronic - Data Table

INSTALLATION
Specication
34 | DHB-E SLi www.stiebel-eltron.com
INSTALLATION | GUARANTEE | ENVIRONMENT AND RECYCLING
Specication
16.7 Data table
DHB-E 11 SLi DHB-E 13 SLi DHB-E 18 SLi 25 A DHB-E 18/21/24 SLi DHB-E 27 SLi
232013 232014 232015 232016 232017
Electrical data
Rated voltage V 380 400 380 400 415 380 400 415 380 400 415 380 400
Rated output kW 10.1 11 12.2 13.5 14.5 16.2 18 19.4 16.2/19/21.7 18/21/24 19.4/22.6/25.8 24.4 27
Rated current A 15.4 16 18.5 19.5 20.2 24.7 26 27 27.6/29.5/33.3 29/31/35 30.1/32.2/36.3 37.1 39
MCB/fuse rating A 16 16 20 20 20 25 25 32 32/32/35 32/32/35 32/32/40 40 40
Phases 3/PE 3/PE 3/PE 3/PE 3/PE
Frequency Hz 50/60 50/60 50/60 50/60 50/- 50/60 50/60 50/- 50/60 50/60 50/- 50/- 50/-
Specific resistance ρ
15
≥ (at ϑcold
≤25°C)
Ω cm 900 900 900 900 1000 900 900 1000 900 900 1000 900 900
Specific conductivity σ
15
≤ (at ϑcold
≤25°C)
μS/cm 1111 1111 1111 1111 1000 1111 1111 1000 1111 1111 1000 1111 1111
Specific resistance ρ
15
≥ (at ϑcold
≤45°C)
Ω cm 1200 1200 1200 1200 1300 1200 1200 1300 1200 1200 1300 1200 1200
Specific conductivity σ
15
≤ (at ϑcold
≤45°C)
μS/cm 833 833 833 833 770 833 833 770 833 833 770 833 833
Max. mains impedance at 50Hz Ω 0.379 0.360 0.347 0.284 0.270 0.260 0.254 0.241
Connections
Water connection G 1/2 A G 1/2 A G 1/2 A G 1/2 A G 1/2 A
Application limits
Max. permissible pressure MPa 1 1 1 1 1
Max. inlet temperature for reheat-
ing
°C 45 45 45 45 45
Values
Max. permissible inlet temperature °C 60 60 60 60 60
On l/min >3.0 >3.0 >3.0 >3.0 >3.0
Flow rate for pressure drop l/min 3.1 3.9 5.2 5.2/6.0/6.9 7.7
Pressure drop at flow rate MPa 0.07 (0.02 with-
out DMB)
0.11 (0.03 without
DMB)
0.08 (0.06 without
DMB)
0.08/0.10/0.13 (0.06/0.08/0.10 without
DMB)
0.16 (0.12 with-
out DMB)
Flow rate limit at l/min 4.0 4.0 7.5 7.5/7.5/8.5 8.5
DHW delivery l/min 5.6 6.9 9.2 9.2/10.7/12.3 13.8
Δϑ on delivery K 28 28 28 28 28
Hydraulic data
Nominal capacity l 0.4 0.4 0.4 0.4 0.4
Versions
Connected load adjustable - - - X -
Temperature setting range °C 30 - 60 30 - 60 30 - 60 30 - 60 30 - 60
Safety category 1 1 1 1 1
Insulating block Plastic Plastic Plastic Plastic Plastic
Heating system heat generator Bare wire Bare wire Bare wire Bare wire Bare wire
Cover and back panel Plastic Plastic Plastic Plastic Plastic
Colour White White White White White
IP rating IP25 IP25 IP25 IP25 IP25
Dimensions
Height mm 478 478 478 478 478
Width mm 225 225 225 225 225
Depth mm 105 105 105 105 105
Weights
Weight kg 3.6 3.6 3.6 3.6 3.6
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant
-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment. After use,
dispose of the various materials in accordance with national
regulations.
Guarantee
The guarantee conditions of our German companies do not
apply to appliances acquired outside of Germany. In countries
where our subsidiaries sell our products a guarantee can only
be issued by those subsidiaries. Such guarantee is only grant-
ed if the subsidiary has issued its own terms of guarantee. No
other guarantee will be granted.
We shall not provide any guarantee for appliances acquired in
countries where we have no subsidiary to sell our products.
This will not aect warranties issued by any importers.
Environment and recycling
We would ask you to help protect the environment.
After use,
dispose of the various materials in accordance with national
regulations.
GUARANTEE
ENVIRONMENT AND RECYCLING