What to do if the starter motor rotates but the engine won't start on my Stiga PARK 120 2016?
If the starter motor rotates, but the engine of your Stiga Lawn Mower won't start, consider replacing the fuel valve or the ignition switch.
Why does the engine not stop on my Stiga Lawn Mower?
If your Stiga Lawn Mower's engine doesn't stop, check the short circuit cable and its connection to the engine. If the issue persists, replace the ignition switch.
How to fix a Stiga PARK 120 2016 when the starter motor does not rotate?
If the starter motor on your Stiga Lawn Mower doesn't rotate, you should correct the problem. Check the starter motor and the battery. Try changing the start relay, the ignition switch, the parking brake switch, or the seat switch (Black).
Why can't I start the blades on my Stiga PARK 120 2016?
If you cannot start the blades on your Stiga Lawn Mower, you may need to change the lifting switch or the seat switch.
Why does the battery discharge repeatedly on my Stiga Lawn Mower?
If the battery of your Stiga Lawn Mower discharges repeatedly, consider replacing the ignition switch or the battery itself. You might also need to repair a fault or replace the charge regulator.
Why can the blades start without anyone sitting on the seat on my Stiga Lawn Mower?
If the blades of your Stiga Lawn Mower can start even without anyone sitting on the seat, replace the seat switch (Black).
How to fix electric height adjustment that does not work on a Stiga PARK 120 2016?
If the electric height adjustment on your Stiga Lawn Mower isn't working, try replacing the switch or the actuator.
What to do if the blades don't stop when lifting the mower deck on my Stiga PARK 120 2016?
If the blades of your Stiga Lawn Mower do not stop when you lift the mower deck, you should replace the lifting switch.
What to do if the blades does not stop when the operator leaves the seat on my Stiga PARK 120 2016 Lawn Mower?
If the blades on your Stiga Lawn Mower do not stop when the operator leaves the seat, you should replace the seat switch.
General| Fuel Type | Petrol |
|---|---|
| Engine Type | 4-stroke |
| Cutting Height | 25-80 mm |
| Displacement | 344 cm³ |
| Drive System | Hydrostatic |
Manual structure, liability, symbols, safety warnings, abbreviations, and spare parts.
Details warranty period, exceptions, reporting faults, and ordering spare parts.
Explains how to identify the machine, transmission, and engine using serial numbers.
Instructions for unpacking, initial assembly, battery installation, and final checks.
Lists maintenance points, intervals, and references for periodic servicing.
Provides machine dimensions, tightening torques, and references the user manual.
Step-by-step guide for removing and refitting engine and front covers.
Procedure for removing and installing the link arm, including safety warnings.
Details lubrication points, actions, and frequency for maintaining the frame.
Explains the mechanical steering system, cables, and gearwheel connection.
Provides instructions for removing and reassembling the steering wheel assembly.
Details how to adjust cable tension, align steering, and check wheel straightness.
Step-by-step guide for replacing worn bushes on the steering shaft.
Emphasizes cleanliness and protection of hydraulic system components during work.
Explains the hydrostatic transmission (HST) components and operation.
Details HST oil type, volume, and conditions for oil filling or change.
Steps for safely removing the transmission, including necessary precautions.
Explains the importance of using genuine belts and their specifications.
Identifies and describes the main belts (A, B, C, D) and their functions.
Detailed procedure for disassembling and assembling the drive belt (D).
Instructions for replacing clutch belt (C) and equipment belt (B).
General information on cable construction, maintenance, and cable tie usage.
Covers adjustment of angle ball joints for cable tension and alignment.
Procedures for disassembling, assembling, and adjusting the HST control cable.
Details brake cable disassembly, assembly, adjustment, and safety warnings.
Procedures for disassembling, assembling, and adjusting the accelerator cable.
Describes electrical components, safety circuits, and fuse protection.
Guide for diagnosing and rectifying electrical faults, including pre-checks.
Explains cable types, connections, and proper handling of electrical wiring.
Instructions for replacing relays, fuses, switches, and battery.
Details the function and operation of control panel switches like A1 and A2.
Visual representation of the machine's electrical circuits for diagnosis.
Explains the benefits and safety aspects of using genuine mower blades.
Step-by-step guide for safely removing and installing mower blades.
Instructions for disassembling, checking, and assembling mower deck belts.
Procedure for disassembling and replacing the mower deck hub.
Explains how to check and ensure correct synchronization of mower blades.
Covers replacement of cylinder/engine lifting components and lift lever spring.
To Next Page