Stylish MODENA K-131 User Manual

C
B
A
E
Ø35mm
WARRANTY
FAUCET INSTALLATION
Ensure there is a Ø35mm
through-hole on the kitchen
counter. Remove the mounting
nut (A) and washer (B) from the
threaded shroud (C).
1
BEFORE YOU BEGIN YOUR INSTALLATION
Products and specifications shown are subject to change without notice. Please contact our technical support at care@stylishkb.com for any further queries, replacement parts requests, etc. ©2021 Stylish
®
all right reserved.
Stylish International Inc. stylish.international.incFollow us on Instagram! Check out and let us know your comments
CARE AND CLEANING
TOLL
FREE
+1-855-789-5352
TOLL
FREE
www.stylishkb.com
care@stylishkb.com
For additional technical assistance or for
any questions or concerns about your
kitchen faucet's warranty, please contact
us.
www.stylishkb.com/warranty
MODENA
K-131
KITCHEN FAUCET
Clean the faucet frequently using mild soap or an on-abrasive
cleaner and then quickly rinse with water and dry with soft cloth
only.
Using abrasive cleaners, solvents, acid cleaners or any scrubbing
detergent, polisher or scraper will damage the finish and void the
warranty.
2
Position faucet on the installation
surface. Fit flexible hoses through
hole on countertop or sink.
Slide washer and thread the
mounting nut onto threaded
shroud. Turn faucet to desired
handle position. Securely tighten
clamp screws (E).
3 4
Secure weight on lowest vertical
point on pull-out hose side.
(not on quick connect side).
5 6
Connect hot and cold water
lines to the inlet pipe and tighten
with a wrench until snug.
Do not over tight.
7 8
Connect braided supply hoses
to faucet female outlets, secure
firmly by hand until hose is snug
to pipe.
Connect pullout hose to quick
connect and insert weight
(loose-install).
Before connecting supply hose,
flush supply valves to clear any
debris. Place a bucket under-
neath valves and run water for 5
to 10 seconds. Turn water off.
Unscrew spray head by hand.
Hold the tip of the spray hose
down and turn on the faucet
and let the water run 60 seconds
to flush any debris,
the re-connect spray head.
Ensure gasket is present.
Shut off
water supply
Flush hot and cold
water supply lines
Required tools Installation by License
Professional Plumber
Flush the water pipe
before installation
Drawings are for
reference only
Do not disassemble
the body

Stylish MODENA K-131 Specifications

General

Brand	Stylish
Model	MODENA K-131
Category	Kitchen & Bath Fixtures
Language	English

Summary

Modena K-131 Kitchen Faucet Installation

Before Faucet Installation

Initial steps include shutting off water, flushing lines, and gathering tools before proceeding with faucet installation.

Install Faucet Body

Position faucet, fit hoses through the hole, and secure the mounting nut and clamp screws.

Connect Faucet Hoses and Weight

Connect supply hoses to faucet outlets, pullout hose to quick connect, and attach the weight.

Flush Water Lines

Flush supply valves and faucet lines to remove debris before final connection and use.

Care and Cleaning Instructions

Clean faucet with mild soap and soft cloth; avoid abrasive cleaners to maintain finish and warranty.

Warranty and Technical Support

Contact Stylish for warranty assistance, technical support, or any questions regarding the faucet.

Lodi K-142 Drinking Water Tap Installation

Before Tap Installation

Ensure water supply is off, flush lines, and prepare the installation area with the correct hole size.

Install Tap Body

Remove the mounting nut from the faucet, insert the tap into the countertop hole, and secure the mounting nut.

Connect Tap Hoses

Connect the appropriate connector size (1/4" or 3/8") to the tap's supply hose.

Check for Leaks and Kinks

Tighten hose connections gently and check for any water leaks or hose kinks after installation.

Tap Care and Cleaning

Clean the tap using mild soap and a soft cloth, avoiding harsh chemicals that could damage the finish.

Tap Warranty and Support

Refer to the warranty section for technical assistance or any concerns related to your drinking water tap.