EasyManua.ls Logo

Sullair VS-32 - User Manual

Sullair VS-32
130 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
SULLAIR ROTARY
VACUUM SYSTEM
VS-32
150-200hp / 113-150kw
OPERATOR’S
MANUAL AND
PARTS LIST
KEEP FOR
FUTURE
REFERENCE
Part Number
02250157-389
©Sullair Corporation

Table of Contents

Questions and Answers

  • P
    Patrick CrossAug 3, 2025
    What to do if my Sullair Vacuum Cleaner won't start?
    • J
      Joel BartlettAug 3, 2025
      If your Sullair Vacuum Cleaner won't start, there are several potential causes. First, check if the main disconnect switch is open and close it. Also, inspect the line fuse and control transformer fuse, replacing them if blown. Additionally, the motor starter overloads might have tripped; reset them, and if the problem continues, verify the motor starter contacts are functioning correctly. Finally, check the incoming line voltage and consult your power company if it's low.
  • M
    mary84Nov 16, 2025
    Why does my Sullair Vacuum Cleaner shut down with vacuum demand present?
    • M
      Mr. Corey Mccarthy PhDNov 16, 2025
      There are several reasons why your Sullair Vacuum Cleaner might shut down while vacuum demand is present. Check for loose wires that could cause a loss of control voltage and replace the control transformer fuse. Low incoming voltage can also be a factor, so consult your power company. Excessive vacuum unit discharge pressure could be due to a defect in the pressure switch; check the pressure at which the contact points open. The separator might require maintenance, so check the maintenance indicator under full load conditions. Also, the high-pressure shutdown switch might be adjusted too low; readjust it to 12 psig (83kPa). Other potential issues include a blockage or closed valve on the discharge line, a discharge line pipe size that is too small, or an open discharge temperature switch ...

Summary

Section 1 SAFETY

GENERAL SAFETY PRECAUTIONS

General safety precautions and responsibilities for safe operation.

PERSONAL PROTECTIVE EQUIPMENT

Requirements for personal protective equipment when installing or operating the vacuum.

PRESSURE RELEASE & FIRE;EXPLOSION

Safety measures for pressure release, fire, and explosion prevention.

MOVING PARTS & HOT SURFACES

Safety regarding moving parts, hot surfaces, sharp edges, and corners.

TOXIC SUBSTANCES & ELECTRICAL SHOCK

Handling toxic substances and preventing electrical shock.

LIFTING & ENTRAPMENT

Safety procedures for lifting, moving, and preventing entrapment.

Section 2 DESCRIPTION

SYSTEM INTRODUCTION & COMPONENTS

Introduction to the system and overview of its components.

FUNCTIONAL DESCRIPTION

Functional descriptions of the vacuum unit, cooling, and lubrication systems.

DISCHARGE & CONTROL SYSTEMS

Functional descriptions of the discharge and control systems.

INLET & INSTRUMENTATION SYSTEMS

Functional descriptions of inlet and instrumentation systems.

Section 3 SPECIFICATIONS

SPECIFICATIONS

Technical specifications for package types, dimensions, and weights.

LUBRICATION GUIDE

Guide for vacuum fluid selection, changing, and maintenance.

VACUUM INLET TEMPERATURE LIMITS

Guidance on inlet temperature limits to prevent condensation.

Section 4 INSTALLATION

MOUNTING & VENTILATION

Requirements for mounting, ventilation, and cooling of the vacuum system.

PIPING, COUPLING, FLUID LEVEL, MOTOR, ELECTRICAL

Installation procedures for piping, coupling, fluid level, motor rotation, and electrical preparation.

RUPTURE DISK

Instructions for installing and handling the rupture disk.

Section 5 OPERATION

GENERAL & PURPOSE OF CONTROLS

General operation overview and explanation of controls and indicators.

INITIAL START-UP PROCEDURE

Step-by-step procedure for the initial start-up of the vacuum system.

SUBSEQUENT START-UP & SHUTDOWN

Procedures for subsequent start-ups and system shutdown.

Section 6 MAINTENANCE

MAINTENANCE SCHEDULES

General, daily, 50-hour, and 4000-hour maintenance tasks.

FLUID FILTER & PARTS REPLACEMENT

Procedures for fluid filter and parts replacement/adjustment.

AIR FILTER & SEPARATOR MAINTENANCE

Procedures for inlet air filter and separator element maintenance.

CONTROL SYSTEM ADJUSTMENT

Procedure for adjusting the Sullicon Control system.

TROUBLESHOOTING

Introduction and guide to identify and resolve common problems.

Section 7 ILLUSTRATIONS AND PARTS LIST

PROCEDURE FOR ORDERING PARTS

Guidelines and contact information for ordering replacement parts.

RECOMMENDED SPARE PARTS LIST

List of recommended spare parts and kits for the vacuum system.

COMPRESSOR, FRAME AND DRIVE ILLUSTRATIONS

Illustrations and parts lists for compressor, frame, and drive assemblies.

AIR INLET & CONTROL ASSEMBLY ILLUSTRATIONS

Illustrations and parts lists for air inlet and control assemblies.

SYSTEM COMPONENTS ILLUSTRATIONS

Illustrations and parts lists for discharge, Sullicon control, piping, cooling, and water piping.

CONTROL SYSTEMS & INSTRUMENT PANELS ILLUSTRATIONS

Illustrations and parts lists for various control systems and instrument panels.

ENCLOSURE & DECAL ILLUSTRATIONS

Illustrations and parts lists for enclosures and decals.

WIRING DIAGRAMS

Wiring diagrams for standard and dual control systems.

Sullair VS-32 Specifications

General IconGeneral
BrandSullair
ModelVS-32
CategoryVacuum Cleaner
LanguageEnglish