Summer 12130B - User Manual

4
INSTRUCTION MANUAL
SURE & SECURE
®
SINGLE BEDRAIL
Please read the following instructions
and warnings carefully.
Keep this instruction manual
for future reference.
Adult assembly required.
For Technical Support Call
1-800-268-6237 or E-Mail at
customerservice@summerinfant.com.
For use with children 2-5 years of age.
SET UP:
TO FOLD DOWN BEDRAIL:
Raise locking pins up on both
sides of the bedrail’s support
leg and fold down bedrail
(Figures P & Q).
QP
TO CLEAN:
To clean this Sure and Secure Single Bedrail, surface wash with damp sponge, mild soap and
cold water. Rinse and lay flat to dry. Do not remove fabric cover from frame.
TO LOOSEN BEDRAIL FOR REMOVAL:
Push release lever up on support leg while pulling
bedrail away from mattress. Repeat on other
end (Figure R).
CAUTION: Do not push strap lock lever down.
R
IMPORTANT NOTE: To Ensure
against entrapment hazards, make
sure there are no gaps between the
bedrail and the mattress. Slight
deformation of the mattress is
acceptable. See diagram at right.
Summer Infant, Inc.
1275 Park East Drive
Woonsocket, RI 02895 USA
1-800-268-6237
© 2007 Summer Infant, Inc.
Please retain information for
future reference.
Summer Infant Europe, LTD.
Office Suite 6, Second Floor
Bournehall House, Bournehall Road
Bushey, Hertfordshire WD 23 3HP
+44 (0) 208 420 4429
Colors and styles may vary.
MADE IN CHINA
6/09
mattress
box spring
12130B/12135B/12150B
(colors & styles may vary)
www.summerinfant.com
We LOVE our customers!
Get to know us at:
We at Summer Infant stand behind all of our products. If
you are not completely satisfied or have any questions,
please contact our customer service department at
1-800-268-6237 or customerservice@summerinfant.com
(For Europe call +44 (0)208 420 4429 or
customerserviceuk@summerinfant.com)
Suffocation and Strangulation Hazard. Death or Serious Injury Can Occur:
• Infants who cannot get in and out of an adult bed without help can be trapped
between a mattress and a wall and suffocate. NEVER place infants in adult beds
with or without bedrail.
• BEDRAIL USE: Bedrail can trap young children against mattress, headboard, or footboard.
• Use only for children who have outgrown a crib. NEVER use in place of a crib.
• Use only with children who can get in and out of adult bed without help.
• ALWAYS keep bedrail pushed firmly against mattress and at least 9 inches from
headboard and footboard.
• NEVER use on toddler bed, bunk bed, water bed, or bed with inflatable mattress.
Use only on adult bed with mattress and box spring or platform bed (support board 5/8"
nominal thickness).
• ENTRAPMENT HAZARD: Death or Serious Injury Can Occur if bedrail is used without
fabric cover. Never use without fabric covering metal frame.
• Discontinue use if damaged,broken, or if parts are missing.
Periodically check the bedrail for tightness to ensure bedrail is snug
against bed.

Summary

Bedrail Setup Instructions

Important Setup Note

Ensure no gap between bedrail and mattress; check for correct mattress deformation.

How to Fold Down Bedrail

Raise locking pins on support leg and fold down bedrail.

Loosening Bedrail for Removal

Push release lever up on support leg while pulling bedrail away from mattress.

Bedrail Cleaning Procedure

Surface wash with damp sponge, mild soap, and cold water. Rinse and lay flat to dry.

Bedrail Features and Components

Single Bedrail Setup Steps

Step 1: Insert Connector Tubes

Insert top, middle, and bottom connector tubes into each end rail.

Step 2: Attach Support Legs

Insert support leg into end of bedrail frame and snap into place.

Step 3: Engage Support Leg Lock

Fold down support legs until spring lock is engaged.

Step 4: Place Fabric Panel

Place fabric panel completely over bedrail frame and slide down.

Step 5: Secure Fabric Cover

Zipper bottom of fabric cover over bottom rail and attach hook & loop flap.

Step 6: Connect Mattress Anchors

Connect mattress anchors to 3-way connector on both sides.

Step 7: Attach Strap Clip

Attach strap clip to 3-way connector with notch facing down.

Step 8: Remove Mattress

Remove mattress from bed to allow for proper bedrail installation.

Step 9: Position Bedrail on Boxspring

Position assembled bedrail on boxspring and pull strap to proper tension.

Step 10: Secure Mattress Straps

Place mattress back, pull strap to proper tension, press lever to lock.

Step 11: Measure Clearance

Ensure bedrail is centered and measure at least 9 inches clearance.

Connecting Two Bedrails for Double Bed

Step 1: Disconnect 3-way Connector

Remove 3-way connector from mattress anchor by pressing button.

Step 2: Connect Two Bedrails

Rotate 3-way connector and connect two single bedrails under mattress.

Step 3: Finalize Double Bedrail Install

Follow steps 7 through 8 of single bedrail installation to finalize.

Summer 12130B Specifications

General

Power Source	Battery
Material	Plastic
Product Type	Baby Monitor
Monitor Features	Two-Way Communication
Features	Two-Way Communication