Sun Moon SM-8800 User Manual

SM-8800 Multi-Function Electronic load (10 in 1)
Hardware User’s manual
Auto/ATE Version
Sun Moon Technology Corp.

Sun Moon SM-8800 Specifications

General

Brand	Sun Moon
Model	SM-8800
Category	Test Equipment
Language	English

Summary

1. Introduction

1-2 Product Specifications

Details the electrical and physical specifications of the SM-8800 DC and AC parts.

Front Panel Controls

Rear Panel Connections

2. Installation Guide

2-1 Power and AC Source Connection

Instructions for connecting the power cord and external AC sources to the SM-8800.

2-3 SM-8800 SPS Connection

Details how to connect the SM-8800 to a Switched-Mode Power Supply (SPS).

2-5 SM-8800 I/O Port Connections

Details the connections for I/O ports and external control circuits of the SM-8800.

3. Operation Panel Guide

3-1 Front Panel Keypad Functions

Describes the function of each key on the SM-8800's front panel, including special key combinations.

3-2 Display Window Information

Explains the various display windows and the information shown on the SM-8800 screen.

3-3 Rear Panel Ports Overview

Details the functions and connections of the ports on the SM-8800 rear panel.

3-4 Standby Mode Parameter Setup

Guides users on setting current and voltage parameters from I1 to I10 in standby mode.

3-5 AC Power Meter Manual Test

Instructions for reading AC power meter test results in manual operation mode.

4. Automatic Test System

4-1 Test Items Specification

Specifies the details and procedures for various automatic test items, focusing on time-related tests.

4-2 AC Meter Test Functions

Details the items tested by the AC power meter when the SM-8800 is configured with it.

5. Parameter Setting Guide

5-1 Manual/Auto Test Mode Switch

Instructions for switching between manual and automatic test modes using the Shift+A function.

5-1-1 Automatic Test Execution

Guides on initiating an automatic test by pressing the AC ON button and interpreting results.

5-2 Channel Total Amount Setting

Explains how to set the total number of channels used in standby mode for tests.

5-3 Auto-Test Parameter Configuration

5-3-1 CONF 1 Parameter Setup

Sets CONF 1 parameters for voltage judgment during repeated booting in automatic tests.

5-3-2 CONF 2 Shared Parameter Setup

5-3-3 CONF 3 AC Power Meter Setup

5-3-4 AC Power Meter Lower Limit Setup

5-3-5 CONF 5 AC Power Meter Setup

5-3-6 CONF 6 AC Power Meter Setup

5-3-7 CONF 7 AC Power Meter Setup

5-3-8 CONF 8 AC Power Meter Setup

5-3-9 CONF 9 AC Power Meter Setup

5-3-10 CONF 10 AC Power Meter Setup

5-3-11 RUN1.1 Auto-Test Program

5-4 Shared Parameter Settings

5-4-1 Time Settings

5-4-2 Rise Time Test Settings

5-4-3 Power Good (PG) Test Settings

5-4-4 PF and Power Off Test Settings

5-4-5 OPP.1 Down Voltage Comparison

5-4-6 OPP.2 Increment Time

5-4-7 OPP.3 Current Increment

5-4-8 OPP.4 Max Current Increment

5-4-9 OPP.5 Over Power Setting

5-4-10 OCP.1 Current Increment

5-4-11 OCP2 Current Increment

5-4-12 OCP3 Current Increment

5-4-13 OCP4 Current Increment

5-4-14 DYN1 Load Setting

5-5 Fast Parameter Setting

5-5-1 Load Selection Interface

5-5-2 Channel Current Setting

5-5-3 Channel Max Voltage Setting

5-5-4 Channel Min Voltage Setting

6. Parameter Management

6-1 Parameter Deletion and Reset