Suncast GLIDETOP BMS4900 - BEFORE YOU BEGIN....; WARNING; ATTENTION; ASSEMBLY DAY TIPS

BEFORE YOU BEGIN....
* Consult your local authorities for any permits required to construct shed. Prior to the construction of your shed, check with the local
building code official to review any required permits or building limitations.
+ A level and sturdy foundation is required before shed construction can begin. Site preparation information is available on page 3.
* Read instructions thoroughly prior to assembly. This kit contains parts that can be damaged if assembled incorrectly or in the wrong
sequence.
* Please follow instructions. Suncast is not responsible for replacing parts lost or damaged due to incorrect assembly.
* Check for all parts before you begin assembly. Using the provided parts check list on pages 4-5, verify that you have all the parts
required to construct your shed model. COMPLETE SITE PREPARATION AND FOUNDATION CONSTRUCTION BEFORE UNPACKING ALL
PARTS.
e Avoid scratching finish. For steps where parts are placed upside down, place parts on a smooth flat surface to avoid scratching finish.
4à WARNING
ed not intended for storage of flammable or caustic chemicals.
ed not intended for use by children. This is not a toy box.
is kit contains parts with metal edges. Please be careful when handling.
ATTENTION
* Do not stand, sit, or store items on storage shed roof.
* Heavy articles should not be leaned against the walls, as this may cause panel distortion and permanent damage.
* Treat carefully in extreme temperatures. This product may become susceptible to impact damage in freezing temperatures.
* Do not store near excessive heat.
* Hot items, such as recently used grills, blowtorches, etc., must not be stored in the shed.
* Shed not intended for use in extreme weather conditions.
e Suncast is not responsible for damage caused by weather or misuse.
ASSEMBLY DAY TIPS
* Complete site preparation and foundation construction before unpacking parts and beginning assembly.
* DO NOT attempt to assemble on a day with strong winds.
* DO NOT attempt to assemble on days when temperature is below 32 degrees.
* Make sure you have assistance nearby to lift and secure parts in place.
* Once roof is assembled, a flashlight may be of use when assembling smaller components inside shed.
* DO NOT use a torque wrench or hand drill to tighten provided Easy Bolts. Use provided Easy Bolt Easy Driver tool ONLY.
* For customer convenience, Suncast provides extra hardware. In some cases, there will be small fasteners remaining, after assembly is complete.
MAINTENANCE
* At regular intervals inspect your shed to make sure that assembly integrity has been maintained.
* Repair or replace broken parts immediately.
* Periodically check that the location you have chosen to set your shed is still level.
* Keep roof clean of snow and leaves.
* The shed walls and roof sections have a textured exterior, much like vinyl home siding. Over time, dust may accumulate in the texture. When
combined with moisture, this could encourage the growth of moss or mold on the shed. To maintain the look of your shed, we recommend cleaning
h mild soap and water. DO NOT use bleach, ammonia, or other caustic cleaners, and DO NOT use stiff bristle brushes. Failure to
d result in permanent staining of the plastic. This is not a manufacturing defect and is not covered under warranty.
it each year wi
perform annual cleaning cou
Suncast® Corporation, 701 North Kirk Road, Batavia, Illinois 60510 (Manufacturer) warrants to the original purchaser only that the enclosed product is free
from material and workmanship defects under normal, household use at time of purchase.
This limited warranty does not apply to damage resulting from accident, neglect, misuse, commercial use, alteration, operation not in accordance with
instruction or repairs made or attempted by unauthorized persons.
This limited warranty applies only to the product enclosed and does not apply to accessory parts.
THE MANUFACTURER'S LIABILITY HEREUNDER IS LIMITED SOLELY TO THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT OR PART AND THE
MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM ANY DEFECT IN
MATERIAL OR WORKMANSHIP OR FROM THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or a limitation of how long an implied warranty lasts, so the
above limitations may not apply to you. This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.