EasyManuals Logo

Sunlight Supply Titan Controls Helios 1 User Manual

Sunlight Supply Titan Controls Helios 1
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
Helios 1 – 120 Volt / 4 Light
Controller Overview
The Helios 1 lighting controller is specically designed for operation of high intensity discharge
(HID) lighting systems. The controller will run your lights for any sequence over a 24 hour
period by using premium German manufactured analog timer. The controller can handle up to
a maximum of four (4) 1000 watt HID metal halide or high pressure sodium (HPS) grow lights.
There is a 120 Volt accessory outlet located on the front of the controller. This outlet is only
active when your lights are ‘ON’ and may be used to power devices up to 5 amps, such as an
in-line lamp ventilation fan or a pump. The Helios 1 lighting controller provides up to 50 amps
of capacity on a standard 120 volt circuit. The Helios 1 is built with only the highest quality
components and will provide the user with years of trouble free service.
Instructions for Operation
*Please consult with a licensed electrician prior to installation of the Helios 1.
*DO NOT install this controller yourself if you DO NOT fully understand these instructions. High
voltage is dangerous!
Connect your incoming 120 Volt power to the 3 screws under the protective back cover.
Black/hot ( left screw), green/ground (center screw) & white/neutral (right screw).
* Securely mount your Helios 1, using the hardware included, near your enclosure and away
from any spray/water/mist, etc.
Hardwire or plug the controller into a conrmed 120 volt power source.
*Verify that all your wiring connections are tight and that no loose wires are exposed.
* Plug your lights into the outlets on the right and left side of the controller.
* Adjust the analog timer to the current time of day. Set your timing pattern by pushing the ‘time
trippers towards the center of the timer.
• Make sure that all wires and cables have been properly secured.
Turn on the power switch to activate your light bank. When the relay is activated you will hear
a “Click” sound.
Your Helios 1 will now control your lights at the desired settings until the power is defeated.
To change your lamps, turn OFF’ the power switch and replace bulb.
Caution: Lamps are hot and should be allowed to cool completely before handling.
Warranty Information
Titan Controls® warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
During the warranty period, Titan Controls® will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and tness for use and of all other obligations or liabilities on the
part of the seller.
This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modication, negligence, alteration or misapplication.
Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts, are excluded from coverage.
Titan Controls® makes no warranty whatsoever in respect to accessories or parts not supplied
by Titan Controls®.
• Monetary refunds of the warranty will not be given.
The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
This warranty shall apply only to the United Sates, including Alaska, Hawaii and territories of the
United States.
• Defective controllers need to be returned with the proof of purchase/receipt”.
For additional warranty information, contact a Titan Controls® Technical Service Representative
or your Dealer.
NOTE: Titan Controls® is a manufacturer of environmental controls. All sales oerings to the
public are done through a nationwide group of Dealers. No sales oerings will be made directly
to the general public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives for a
Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller and after
authorization by customer for repairs.
Titan Controls® will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls®.
• Returning Units: Please contact your retail store for returns.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sunlight Supply Titan Controls Helios 1 and is the answer not in the manual?

Sunlight Supply Titan Controls Helios 1 Specifications

General IconGeneral
BrandSunlight Supply
ModelTitan Controls Helios 1
CategoryController
LanguageEnglish

Related product manuals