SunPower X Series - Page 8

MAXEON SOLAR TECHNOLOGIES, LTD.
Safety and Installation Instructions - Document 001-15497 Rev.AA
©June 2023 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Appendix: Mounting Configurations and Load Ratings
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
50 - 150
Design Load

Long Side Mounng,
Rails Perpendincular
Long Side Mounng,
Point Supported
Long Side Mounng,
Rails Parallel to
Mounng Frame
Short Side Mounng,
Point Supported
(End Mount)
Short Side Mounng,
Rails Perpendicular to
Mounng Frame
Short Side Mounng,
Rails Parallel to
Mounng Frame
(End Mount)
150 - 254
254 - 423

423 - 646 
50 - 150
150 - 254
254 - 423
423 - 646
50 - 150
150 - 254
254 - 423
423 - 646
0 - 350

0 - 350
0 - 350
+2700/-2700
+2700/-2700
+2700/-2700
Test Load

+1800/-1800
+1800/-1800
+1800/-1800
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
TOP CLAMPS
SunPower Maxeon 3 104 cells Commercial Solar Panel
(SPR-MAX3-XXX-COM)
0
0
GEN 4.2 FRAME PROFILE
SIDE FRAME PROFILE
END FRAME PROFILE
A - Ground Holes (4X Ø4.2mm)
B - Slots (4X 5.0mm(W) x 15mm (L))
C - Mounng Holes (20X Ø6.8mm)
24mm
40mm
32mm
40mm
Mounng
Configuraon
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
1423mm Holes
Design Load

Long Side Mounng,
Rails Perpendincular
to Mounng Frame
Long Side Mounng,
Point Supported
1200mm Holes
539mm Holes
Test Load

+5400/-3600
+5400/-3600
+5400/-3600
+8100/-3600
+8100/-3600
+3600/-2400
+3600/-2400
+3600/-2400
+5400/-2400
+5400/-2400
400mm Holes
400mm Holes
BOLTS
1423mm Holes
1200mm Holes
539mm Holes
+2400/-2400
+3600/-3600
+3600/-3600
+2400/-2400
+5400/-3600
+3600/-2400
1046 mm
1058 mm
1200 mm
1520 mm
1690 mm
0
C
254
423
150
646
0
254
423
150
646
350
A
50
50
350
B
400 mm
539 mm
1423 mm
1623 mm
Downward/Upward
(Pa)
Downward/Upward
(Pa)
Downward/Upward
(Pa)
Downward/Upward
(Pa)
4 Rails must not be under the juncon box.
Descripon 
Mounng
Configuraon
Descripon

to Mounng Frame 
(End Mount) 
1 In the cases where hybrid mounng is necessary (combinaon of long and short side mounng), the lowest
design load values should be considered as allowable design load.
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
2 Test loads are for informaon purposes only, design loads should be considered for the project design.
5
I
E
C
6
1
7
3
0
C
e
r
t
Te
s
t
e
d
pares, unless there is a formal authorizaon by Maxeon.
Measurement Tolerances are +/-3mm for the Length and Width of the module.


6 Boom flange mounng.
7 Range indicates posioning of the clamp and not the rails.
