SunPower X Series - Page 9

MAXEON SOLAR TECHNOLOGIES, LTD.
Safety and Installation Instructions - Document 001-15497 Rev.AA
©June 2023 Maxeon Solar Technologies, Ltd. All rights reserved. Specifications included in this manual are subject to change without notice.
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
50 - 150
Design Load

Long Side Mounng,
Point Supported
Long Side Mounng,
Rails Parallel to
Mounng Frame
Short Side Mounng,
Point Supported
(End Mount)
Short Side Mounng,
Rails Parallel to
Mounng Frame
(End Mount)
150 - 254
254 - 423

423 - 646
50 - 150
150 - 254
254 - 423
423 - 646
50 - 150
150 - 254
254 - 423
423 - 646
0 - 350

0 - 350
0 - 350
+2700/-2700
+2700/-2700
+2700/-2700
Test Load

+1800/-1800
+1800/-1800
+1800/-1800
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+3600/-3600
+5400/-5400
+3600/-3600
+2700/-2700
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
+2400/-2400
+3600/-3600
+2400/-2400
+1800/-1800
Mounng Configuraon Diagram
Front View
Back View
Mounng Zone
Locaons
(distance from corner
in mm)
Design Load

Long Side Mounng,
Rails Perpendincular
to Mounng Frame
Long Side Mounng,
Point Supported
1300mm Holes
Test Load

+8100/-3600
+8100/-3600
+5400/-2400
+5400/-2400
1100mm Holes
400mm Holes
TOP CLAMPS
BOLTS
SunPower Maxeon 3 104 cells Residenal Solar Panel
(SPR-MAX3-XXX, SPR-MAX3-XXX-BLK)
1046 mm
1002 mm
1100 mm
1300 mm
1500 mm
1690 mm
0
B
3 Design Load considers 1.5 Factor of Safety, Test load = Design load x 1.5. Product Warranty covers only design
load values. The design loads listed in this table supersede all other loads that may be defined by other
254
423
150
646
0
254
423
150
646
0
350
0
350
A
GEN 4.2 FRAME PROFILE
SIDE FRAME PROFILE
END FRAME PROFILE
1300mm Holes
A - Ground Holes (4X Ø4.2mm)
B - Mounng Holes (8X Ø6.8mm)
+3600/-2400
+5400/-3600
+5400/-3600
+3600/-2400
50
50
32 mm
40 mm
24 mm
40 mm
2 Test loads are for informaon purposes only, design loads should be considered for the project design.
5
I
E
C
6
1
7
3
0
C
e
r
t
Te
s
t
e
d
Downward/Upward
(Pa)
Downward/Upward
(Pa)
Downward/Upward
(Pa)
Downward/Upward
(Pa)
4 Rails must not be under the juncon box.
Mounng
Configuraon
Descripon

Mounng
Configuraon
Descripon

Short Side Mounng,
Rails Perpendicular to
Mounng Frame
(End Mount)

Long Side Mounng,
Rails Perpendincular
to Mounng Frame

1 In the cases where hybrid mounng is necessary (combinaon of long and short side mounng), the lowest
design load values should be considered as allowable design load.
pares, unless there is a formal authorizaon by Maxeon.
Measurement Tolerances are +/-3 mm for the Length and Width of the Module.
6 Boom Flange Mounng.
7 Range indicates posioning of the clamp and not the rails.


