Need help?Do you have a question about the Sunstream SunLift SLX 5010 and is the answer not in the manual?
Identifies key components of the 2-cylinder SunLift model.
Identifies key components of the 4-cylinder SunLift model.
List of available leg options for the SunLift models.
Components and part numbers for the SLX 5010 model.
Components and part numbers for the SLX 6512 model.
Components and part numbers for the SLX 8012 and SLX 9012 models.
Components and part numbers for the SLX 10014 model.
Components and part numbers for the SLX 12016 model.
Visual guide for easier boat loading.
Bump stop to prevent over-loading the boat bow.
Raises H-frame/bunk height for water level fluctuations.
Increases footprint size for muddy applications.
Four Button transmitter for lift operation.
Prevents unintended motor operation.
Optional lighting for the lift.
Brackets for attaching catwalks.
Shelf for mounting the powerpack.
Powerpack mounted on the lift legs.
Stiffeners for guide-ons.
Kit for sacrificial anodes (zincs).
Extensions for hydraulic hoses.
Pads for guide-ons.
Guides for load translation.
List of tools needed for assembling the SunLift.
Important note on preparing the assembly area.
Instructions for assembling the legs and foot pads.
Details on leg parts, bolts, nuts, and caps.
Procedure for attaching legs to the crossbeam.
Specifics on bolts and washers for leg connection.
Alternative method for shallow water installations.
Procedure for connecting sidebeams to crossbeams.
Specifies narrow, standard, wide, and extra wide settings.
Tip for easier sidebeam adjustment using grease.
Procedure and settings for H-frame width.
Instructions for connecting the rear H-frame.
Reminder to apply marine grease to all pins.
Procedure for the 2-cylinder forward H-frame.
Reminder to apply marine grease to all pins.
Procedure for the 4-cylinder forward H-frame.
Reminder to apply marine grease to all pins.
Instructions for attaching cylinder pins to rod and barrel.
Reminder to apply marine grease to all pins.
Procedure for routing hydraulic hoses on 2-cylinder lifts.
Procedure for routing hydraulic hoses on 4-cylinder lifts.
Procedure for attaching the final frame parts.
Reminder to apply marine grease to all pins.
Instructions for connecting hydraulic quick disconnects.
Important note on tightening QD fittings to avoid cross-threading.
Verify all bolts and cotter pins are secure and properly installed.
Importance and replacement of sacrificial zinc anodes.
Instructions for preparing the hydraulic system and fluid.
Procedure for testing the lift before water use.
Procedure and considerations for launching the lift into water.
Determining optimal lift depth based on water level fluctuations.
Step-by-step guide for floating the lift into position.
Ensuring the lift is level at all four corners.
Instructions for attaching optional deep water braces.
Final check of all bolts and nuts for security.
Methods for anchoring on steep slopes.
Precautions and procedure for lifting the boat for the first time.
Recommendation for annual inspection by a qualified person.
Tips for storing the lift and boat during off-season.
Recommendations for battery type, capacity, and charging.
Information on lifting cycles based on solar charging.
Operation, programming, and security modes for the remote.
Guidance for installing the RC401 unit.
Indicator for low battery voltage and charging.
Connecting and controlling optional lights.
Locking the keypad and customizing security codes.
Solutions for common RC401 operational issues.
Solutions for lift not operating with switches or transmitters.
Troubleshooting limited remote control range.
Diagnosing and resolving battery charging problems.
Solutions for difficult or impossible hose connections.
Addressing fluid found in the power pack or leaks.
Checking battery terminal connections for optimal function.
Determining skills, knowledge, and tools for assembly/installation.
Importance of proper boat support and manufacturer recommendations.
General safety warnings and guidelines for use.
Specific hazards that can result in serious injury or death.
Specific hazards that could result in serious injury or death.
Specific hazards that could result in minor or moderate injury.
Rules regarding lift capacity, usage, and supervision.
Safest position for the boat on the lift.
Ensuring lift remains level for safety and performance.
Warning against using the powerpack box for storage.
Care and precautions for lifting the boat initially.
Warning against standing or walking on catwalks.
Notice regarding disconnecting hydraulics with a loaded lift.
Information on powering the boat on the lift.
Details on the 3-year warranty for manufacturing defects.
Procedures for reporting and resolving defects.
Damages and conditions not covered by the warranty.
Requirements for annual inspection and part maintenance.
Specific maintenance and exclusions for salt water use.
Procedures for international warranty claims and parts.
Disclaimers of implied warranties and remedy limitations.
General| Brand | Sunstream |
|---|---|
| Model | SunLift SLX 5010 |
| Category | Boating Equipment |
| Language | English |
To Next Page
