Need help?Do you have a question about the SuperLead 5130HS-QD and is the answer not in the manual?
Provides programming instructions for the SuperLead 2D Barcode Reader and how to configure it using programming barcodes.
Restores the scanner engine to its factory default settings by scanning a specific barcode.
Displays the firmware version number of the scanner by scanning a barcode.
Displays the firmware version number of the cradle by scanning a barcode.
Configures scanner Bluetooth settings, connection methods like keyboard or serial port.
Establishes a connection between the scanner and the Bluetooth cradle by scanning a barcode.
Configures the scanner to operate as a Bluetooth keyboard for wireless data input.
Configures the scanner to operate as a Bluetooth serial port for data transmission.
Selects the keyboard layout for Bluetooth keyboard mode based on country-specific requirements.
Converts scanned barcode data to uppercase, lowercase, or no case conversion.
Switches the input method for Bluetooth terminals, including Windows/Android and iOS.
Configures the power state of the scanner, including a 'Power Off' option.
Sets the time duration before the scanner automatically powers off due to inactivity.
Configures settings for the Bluetooth cradle or dongle, including factory defaults and connection parameters.
Restores the cradle's settings to factory defaults by scanning a specific barcode.
Sets the baud rate for serial communication to match host requirements.
Configures data bits, parity check, and stop bits for serial communication.
Enables USB HID-KB feature for keyboard input via USB connection.
Allows the host to receive data as a serial port via USB connection, requiring a driver.
Sets the scanner to synchronous data transfer mode when connected via Bluetooth.
Sets the scanner to asynchronous data transfer mode, storing data when disconnected.
Enables mass storage mode for the scanner, allowing data to be stored and uploaded.
Configures scanner activation via external hardware trigger or serial command for manual or serial modes.
Sets the scanner to operate in presentation mode for automatic scanning when objects are presented.
Controls inverse color display for barcodes, with options for ON, OFF, and Both.
Adjusts illumination levels for manual trigger mode and presentation mode scanning.
Enables or disables the beeper that signals a successful barcode read.
Sets the volume level for the good read beeper (Low, Middle, High).
Enables or disables vibration feedback upon a successful barcode read.
Configures the delay time after a successful read before the next scan can occur.
Sets the delay time between consecutive reads of the same barcode.
Sets general data formatting options like adding CR, LF, CRLF, or TAB characters to scanned data.
Adds a custom prefix to scanned barcode data, configurable via specific barcodes.
Adds a custom suffix to scanned barcode data, configurable via specific barcodes.
Clears all configured prefixes and suffixes from the scanner settings.
Provides general settings for barcode symbologies, including enabling or disabling all.
Enables or disables all supported barcode symbologies simultaneously.
Enables or disables the Code 128 barcode symbology and its specific settings like message length.
Enables/disables EAN-8 symbology and configures check digit transmission and add-on codes.
Configures the scanner to read EAN-8 barcodes with two-digit or five-digit add-on codes.
Sets whether EAN-8 barcodes must have an add-on code to be read.
Configures a space as a separator between EAN-8 barcodes and their addenda.
Enables or disables the EAN-13 barcode symbology and its related settings.
Configures the transmission of the check digit for EAN-13 barcodes.
Configures the scanner to read EAN-13 barcodes with two-digit or five-digit add-on codes.
Sets whether EAN-13 barcodes must have an add-on code to be read.
Configures a space as a separator between EAN-13 barcodes and their addenda.
Translates EAN-13 Book land symbols into their equivalent ISBN number format.
Enables or disables UPC-E0/E1 symbologies and configures related settings.
Configures the transmission of the check digit for UPC-E0 barcodes.
Expands the UPC-E code to the 12-digit UPC-A format.
Sets whether UPC-E barcodes must have addenda to be read.
Configures a separator for UPC-E addenda.
Controls the transmission of the number system digit for UPC-E0 symbols.
Configures the scanner to read UPC-E0 barcodes with two-digit or five-digit addenda.
Enables or disables the UPC-A barcode symbology and its related settings.
Configures the transmission of the check digit for UPC-A barcodes.
Sets whether UPC-A barcodes must have addenda to be read.
Configures a separator for UPC-A addenda.
Controls the transmission of the number system digit for UPC-A symbols.
Configures the scanner to read UPC-A barcodes with two-digit or five-digit addenda.
Enables or disables the Interleaved 2 Of 5 barcode symbology and its related settings.
Sets the minimum and maximum message length for Interleaved 2 Of 5 barcodes.
Configures check digit validation and transmission for Interleaved 2 Of 5 barcodes.
Enables or disables the Matrix 2 Of 5 barcode symbology and its related settings.
Sets the minimum and maximum message length for Matrix 2 Of 5 barcodes.
Enables or disables the Industrial 2 Of 5 barcode symbology and its related settings.
Sets the minimum and maximum message length for Industrial 2 Of 5 barcodes.
Enables or disables the Code 39 barcode symbology and its related settings.
Configures the transmission of start and stop characters for Code 39 barcodes.
Configures check character validation and transmission for Code 39 barcodes.
Allows appending multiple Code 39 barcode data together before transmitting to the host.
Enables or disables the full ASCII character set for Code 39 barcodes.
Sets the minimum and maximum message length for Code 39 barcodes.
Enables or disables the Coda Bar barcode symbology and its related settings.
Sets the minimum and maximum message length for Coda Bar barcodes.
Configures the transmission of start and stop characters for Coda Bar barcodes.
Configures check character validation and transmission for Coda Bar barcodes.
Enables or disables the Code 93 barcode symbology and its related settings.
Sets the minimum and maximum message length for Code 93 barcodes.
Allows appending multiple Code 93 barcode data together before transmitting to the host.
Enables or disables the GS1-128 barcode symbology and its related settings.
Sets the minimum and maximum message length for GS1-128 barcodes.
Enables or disables the Code 11 barcode symbology and its related settings.
Configures check digit validation for Code 11 barcodes (one or two digits).
Enables or disables PDF 417 and Micro PDF 417 symbologies and related settings.
Sets the minimum and maximum message length for PDF 417 barcodes.
Enables or disables the QR Code symbology and its related settings.
Sets the minimum and maximum message length for QR Code barcodes.
Allows appending multiple QR Code data together before transmitting to the host.
Enables or disables the Data Matrix barcode symbology and its related settings.
Sets the minimum and maximum message length for Data Matrix barcodes.
Enables or disables the Maxi code barcode symbology and its related settings.
Sets the minimum and maximum message length for Maxi code barcodes.
Enables or disables the Aztec barcode symbology and its related settings.
Sets the minimum and maximum message length for Aztec barcodes.
Provides a table mapping symbologies to their AIM IDs and remarks.
Lists ASCII characters with their corresponding Hex and Decimal values.
Displays digit barcodes (0-9, A-F) used for scanner configuration.
General| Brand | SuperLead |
|---|---|
| Model | 5130HS-QD |
| Category | Barcode Reader |
| Language | English |
To Next Page
