SuperLead X25 - User Manual

苏州斯普锐智能系统股份有限公司
全国服务热线：400-850-8151 转 3 工业咨询
官网：www.superlead.com
E-mail: sales@superlead.com
地址：中国-江苏省苏州市工业园区东富路 2 号东景工业坊 57 栋
斯普锐（深圳）智能识别有限公司
深圳市龙华区大浪街道潜龙曼海宁广场 16E
E-mail：stan@superlead.com
① 包装清单 Parts List
② 连接系统 Connect to system
首次使用，根据所选购的的电缆，按照上图安装连接读码器。
(1) 连接电缆至读码器 12PIN 连接器；
(2) 连接 5~30V 直流外部供电。使用 USB 接口时可以不连接外部供
电；
(3) 将通讯口连接至 PC 或数据采集终端，支持 TCP/IP，USB
Keyboard, RS232 通讯方式；
(4) 如果使用“触发模式”，需要连接外部传感器/PLC（见接线
图③④⑤）至 PIN 脚 IN，或者通过串口指令控制；
(5) 如果需要读码器输出读码反馈信号或者控制信号，连接 PIN 脚
OUT 至外部设备（见接线图⑥⑦）
First time to use, please follow the instruction and connect scanner to your system,
(1) Connect Scanner and cable by 12PIN connector.
(2) Connect to 5~30V DC external power. External power is not needed when using
USB cable.
(3) Connect communicate port to PC or data collection device. TCP/IP, USB Keyboard
RS232 communication is supported.
(4) If use “Trigger Mode”, you should connect “IN” PIN to an external switch or PLC
(See figure③④⑤). Serial command is also available to trigger scanner
(5) If need scanner output good read signal or other control signal, you should connect
“OUT” PIN to external device(see figure⑥⑦)
③ PNP 光电开关输入 Input connection of PNP Photoelectric Switch
④ NPN 光电开关输入 Input connection of NPN Photoelectric Switch
⑤ 继电器输入 Input connection of Relay Switch
⑥ PNP 信号输出接法 PNP Output Connect
X25 快速手册
Quick Start
66MEXXXX-A-00
主机*1
Main Engine*1
固定支架*1
，螺丝
*2
Mounting bracket*1, Screw*2
快速手册*1
Quick Start*1
X25 快速手册
Quick Start

Summary

Parts List

Main Engine and Mounting Kit

Includes main engine, mounting bracket, and screws.

Quick Start Manual

Includes the quick start manual for the device.

Connect to System

PNP Photoelectric Switch Input

Input connection for PNP photoelectric switches.

NPN Photoelectric Switch Input

Input connection for NPN photoelectric switches.

Relay Switch Input

Input connection for relay switches.

PNP Signal Output

Output connection for PNP signal output.

NPN Output Connection

Bracket Assembly

Bracket Assembly Instructions

Instructions for assembling the mounting bracket using M2.5 screws.

PC Configuration Tool

Superconfig Software

Download and use Superconfig for scanner configuration and debugging.

Common Commands

Trigger Scan Command

Command to initiate a scan operation.

Release Scan Command

Command to stop scanning.

Restore Default Settings

Command to restore default settings.

Query Firmware Version

Command to query firmware version.

Parameter List

Model and Dimensions

Scanner model (X25) and physical dimensions.

Performance Specifications

Includes frame rate, pixel count, and read distance.

Electrical and Interface Specs

Details power voltage, consumption, and supported interfaces.

Environmental and Safety Ratings

Covers operating temperature, humidity, IP rating, and safety standards.

Test Codes

SuperLead X25 Specifications

General

Brand	SuperLead
Model	X25
Category	Barcode Reader
Language	English