Swagman 64671 XTC2 Tilt - User Manual

INSTRUCTION SHEET
PRODUCT: 64671 XTC2 Tilt • Page 1 of 3
300 - 1880 Government St. • Penticton, B.C. Canada V2A 7J1 • Phone (250) 490-8883 • Fax (250) 490-8885 • www.swagman.net
REV 23/10/19
Assembly Instructions
1. Attach the 1-1/4 “ receiver bar to the main assembly
using the 12mm x 60mm bolt, washer and nut. Put the
spring clip security lanyard and 3/8” Lynch pin on the
bolt before inserting.
2. Using the 8mm Allen wrench insert and tighten the
folding guide bolt (diagram 1). NOTE: Make sure to
insert the bolt from the proper side. The guide bolt head
 ts into the slot. Refer to diagram 1.
3. Insert the lynch pin into the hole provide and attached
the spring clip. NOTE: This lynch pin is removed if
folding the bike rack away from the vehicle (diagram 1).
4. Slide the hooks onto the upright portion alternating the
direction (diagram 2).
5. Unfold the two side arms as shown (diagram 2) and
insert 2 lynch pins. Ensure that the pins are all the way
in. Slide the hooks onto the upright portion alternating
the direction
6. Slide the 4 wheel holder trays on to the bottom arms
alternating the direction of the trays (diagram 3). Do
not tighten them at this time, as they will have to be
adjusted to  t each bike that you are carrying.
7. After the wheel holders are installed you will need to
screw in the 2 metal screws at the end of each arm. This
will prevent wheel holders from coming o (diagram 4).
8. Take the bike rack and install into the vehicle hitch.
Install the threaded pin and clip and tighten to
50 ft. lbs. (tight).
9. If the rack is to be used on 1-1/4” receiver you will need
to remove the Allen Bolt that hold on the spacers. Use
the 6mm Allen Wrench (diagram 5).
Installing the Rack Into Your Vehicle:
1. Insert the bike rack into the 2” or 1-1/4 “ receiver. Install
the ½” threaded locking hitch pin and tighten to 50 ft
lbs. (very tight). Put on the lock head until it is securely
attached.
2. The rack is designed to carry up to two 35 lbs. bikes. You
cannot combine weight to carry one bike over 35 lbs.
1
Parts List
12mm x 60mm
Hitch
Pin Clip
Allen Keys
Self Taping
Screws
8mm
Guide Bolt
3/8” Lynch Pin
with Spring
Clip
LYNCH PIN WITH
SPRING CLIP
1/2” Threaded
Hitch Pin

Summary

Assembly Instructions

Attach Receiver Bar

Connect the 1-1/4" receiver bar to the main assembly using the 12mm bolt, washer, and nut.

Install Folding Guide Bolt

Insert and tighten the folding guide bolt using the 8mm Allen wrench, ensuring correct orientation.

Insert Lynch Pin

Place the lynch pin in the provided hole and attach the spring clip for rack folding.

Attach Wheel Holder Trays

Slide the 4 wheel holder trays onto the bottom arms, alternating their direction.

Secure Wheel Holders

Screw metal screws into the end of each arm to prevent wheel holders from detaching.

Install Rack Into Vehicle

Mounting Procedure

Insert the bike rack into the vehicle hitch and secure with the threaded pin and clip.

Receiver Size Adjustment

Remove Allen bolt for spacers if using a 1-1/4" receiver.

Rack Capacity and Weight Limit

The rack carries up to two 35 lbs bikes; do not exceed this limit per bike.

Bike Loading and Securing

Prepare Rack for Loading

Fold down the upright arm by pulling the pin to facilitate loading the inside bike.

Adjust and Tighten Wheel Trays

Adjust trays to fit bike wheels and tighten knobs securely.

Secure Bike with Hook

Lower hook onto bike's top tube, press button to slide, release to lock securely.

Final Check and Tilt Access

Ensure all pins are tight, bikes are motionless, and remove pin to tilt rack.

Important Safety and Usage Notes

Bike and Weight Limitations

Designed for 1-2 bikes, max 35 lbs each; do not combine weight for one bike.

Recommended Usage Conditions

Use on paved or smooth gravel roads; avoid rough roads or vehicles with stiff springs.

Padding and Clearance

Use padding where bikes touch; keep tires/rims 6" from exhaust pipes.

Mounting on Trailers;5 th Wheels

Load exceeds trailer bumper strength; rack is not warranted if mounted here.

Swagman 64671 XTC2 Tilt Specifications

General

Model	64671 XTC2 Tilt
Capacity	2 Bikes
Max Bike Weight	35 lbs per bike
Weight Capacity	70 lbs
Tilt Feature	Yes
Foldable	Yes
Material	Steel
Finish	Black powder coat
Wheel Holders	Adjustable
Type	Hitch-mounted bike rack
Hitch Compatibility	1 1/4" and 2" receiver
Security Features	Locking hitch pin
Frame Holders	Padded