T-Rex BILLET Series User Manual

Page 1
START HERE
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE INSTALLATION.
Auto makers offer varied models to each vehicle and occasionally manufacture more
than one body style of the same model. To assure your part is correct; our tech
department can be contacted at tech@trexbillet.com to verify fitment and assist with
technical questions. All other inquires can be directed to info@trexbillet.com. In the
event you do not have internet access please call 1-800-287-5900.
STEP 1
1) Turn off engine and chalk tires
with stop block. Open Hood.
STEPS 2-4
2) Lay out the 2-piece (Top & Bottom)
3) Sort out the provided hardware and
install the 3” screws into their tabs.
There will be (2) on the top piece and
(2) on the bottom piece.
4) Thread the “Toggle Wing” nuts
over the screws.
* APPLICATION MODELS VARY. WE RECOMMEND TO VERIFY FITMENT BEFORE BEGINNING INSTALLATION PROCESS.
* IMAGES FEATURED IN THE INSTRUCTION DOCUMENTS MAY NOT ALWAYS EXACTLY MATCH YOUR GRILL / VEHICLE.
DISASSEMBLY
SEE FIGURE 1 & 2
PRO TIP:
NOTE BEFORE INSTALL:
Before you begin, use “3M Painters Tape” to apply
a protective guard around the work areas. Attend
to exposed chrome, fender bumper valance. This
will help protect the paint and finish of your vehicle.
This is a Grille Overlay. Your factory grille components and
other vehicle front end features may be visible once your new
grille is fully installed. To counter this visual element, we have
found that you can hide or mostly eliminate the components
by blacking out with flat black aerosol spray paint, plasti-dip
or any other similar product. If you choose to take on this
extra modification, you are advised to mask off any parts or
panels that you do not wish to paint over.
T-REX TRUCK PRODUCTS DOES NOT TAKE ON ANY
RESPONSIBILITY FOR THIS ADDITIONAL MODIFICATION.
FIG 1
FIG 2
* Image of Hardware
(1) Main Grille Overlay (2-Piece)
Polished - Part #21267 OR
Black - Part #21267B
(1) T-REX Logo Sticker
(4) 2.5” Threaded Screws
(4) “Toggle Wing“ Nuts
(2) #8 Self Tapping Screws
- Screwdriver Set
- Drill w/ screw tip
- Flash Light
Tools Required
Hardware included
Parts included
BILLET SERIES Grille
Main grille - #21267 / #21267B
2015 CHEVROLET COLORADO
Grille Installation Guide

T-Rex BILLET Series Specifications

General

Material	Billet aluminum
Finish	Polished
Compatibility	Varies by specific model (check product listing)
Installation	Bolt-on
Weight	Varies by part
Warranty	Limited lifetime warranty

Summary

Grille Installation Process

Notes Before Installation

Important considerations and warnings before starting the grille installation process.

Included Parts and Hardware

Lists all grille components, stickers, and fasteners provided with the kit.

Required Tools

Lists the essential tools needed for the installation of the grille.

Disassembly and Preparation

Initial steps including safety precautions and preparing the vehicle for installation.

Grille Assembly and Attachment

Details on how to assemble hardware with grille pieces and attach them to the vehicle.

Grille Installation Steps

Step 5: Hardware Configuration

Guidance on configuring hardware for correct orientation before installation.

Step 6: Bottom Grille Placement

Instructions for positioning and aligning the bottom grille overlay.

Steps 7-8: Securing Grille

Process for attaching the grille overlay using screws and toggle wing nuts.

Steps 9-10: Top Grille Placement

Instructions for positioning, aligning, and securing the upper grille overlay.

Post-Installation Inspection

Step 11: Visual Inspection

Examining gap alignments and overall fit after installation for proper appearance.

Product Warranty and Care

T-REX Grilles Product Warranty

Details the warranty coverage and limitations for T-REX grille products.

LED Lighting Installation Disclaimer

Important warnings and advice regarding the installation of LED lighting equipment.

Grille Care Information

Guidelines for maintaining the finish of polished, matte black, and gloss black grilles.