Tamiya COMICAL HORNET User Manual

|TEI\,1 58666
EOfUilCALHORNET HH
lEälLfi-äyF
aE@rii.rti.
wR-02c8)rr-7t.fEEz"-+*!: wR-02.
wR-02c. wR-02G2rr-7trt*f€Hz"äsü4,.
aThis
body is for use with
theWR-02C8 chassis.lt is not compatible with theWR-02, WB-02C and WB-02G.
f i
4
OtT) U
W.U
.r
i*
Bt!
6t
d)t 3nn
f-
t
)
) v.
i i l )
-= -
(.5
-snnRfr) ä-FEE< /:t1..
Trim ming
x 3mm drill and bodv reamer a.e requned when making holes-
*5.5m,\äf*3rr*r.
*[,lake
5.5mm holes.
A*a
az:o)+ , |ßßAri<A;twt.
t+
ääfl.ä.ä SdEiEEä ä
E1€*
<"J5#
,9<
ratt\. *t.,1\+t/;8@18+ffi
ah tr1ßarnT A LZ ß.
l#fr+.
o)X
+,
ä#a<r:*L'"
arF@t€Hr.{r+ä,}äL?<
r:tL\.
#t
:..,
1 l-\r
r4
-2
re
tr+kt l-6,
f i55&ti;iELz< r:-*L\^
a*ääl &AX,l ll. fFE-d-äE*{.Zir?
I ft @;tg=*ät<=rt3*. €;t.ft
,rtr
L<f€.8 Lz.< l:tL\" :EL. fFHtae
-+täE^nl&5ti+ä;tELZ<f::!1."
a
4\t
tati+lö@L,68-frv 0)T1Gtt
LfdLrr< tii!L\.
rEIi.!b,7'
r,
,J\-*
rr./
l-,rcD
fia*;Äalt,
E:-rU§
ää.,ii,<@
ger:j
ä,El&ijüiEn'äi
anit"
7
=
<t n*15
tv
Lh'f.)t,
<</:i!L'.
A
cnurol
aRead
carefulty and fully
undeßtand
the instructions before commencing
awhen
assemblins this kit, iools in-
cludins knives are used. Extra care
should
b€ taken to avoid
personal
injury.
aRead
and follow the inslructions
supplied with
paints
and/orcement, if
used
(not
included in kit).
aKeep
out of
reach
of smallchildren.
Children must not be allowed to
put
any
parts
in their mouths, or
pull
vinyl
bass over their heads. Sensibly dis'
pose
of
the leflover
parts
immediately.
«^?4 ar rwt)»
Trimming
iL
*7>TttllJRARaE)I *t^
*lvlake
hole for antenna
pipe.
*3mm'rä83t,*i.-
1l
*5.5mmiäB:t,*n.
*gl,W.,.I
>t
)ä)<.7!\ral\t.ür,ry?<-<i:t !\.
*Cutoutwith
care, keeping 1o cut line.
*3mn
,\z F*3
r,
* li,
T 7--..
-l-\
6mm(ll
r
\..-.. .-_-/
*6mmnä2rF§,jZi'B.
ie)t<J:at
+trw)*t.
*Maketwo 6mh holes ftst.
then
remove
section between
*3mmhär,:l,*r-
*7>Vtt14)RARAffiü*.'t.
*Make
hole
ior antenna
pipe.
x
di;, äry,1
1i,räHi!i.J?<iJ.
,\@iüEä\änr& L * !-.
*Hole
posilion
varies according to
the helsht the body is secu red at,
* l-.>7r1,:/4-77-LL<
-+lH<
l:ill'"
*Use as atransponder stay.

Tamiya COMICAL HORNET Specifications

General

Scale	1:10
Drive type	2-wheel drive (2WD)
Motor type	Brushed
Engine type	-
Product type	Car
Housing material	Acrylonitrile butadiene styrene (ABS)
Construction type	Assembly kit
Bearing technology	Plastic bushing

Weight and Dimensions

Width	244 mm
Length	356 mm
Weight	- g
Wheelbase	170 mm

Summary

Body Trimming and Preparation

Trimming the Body Shell

Instructions for cutting out the car body panels according to markings.

Drilling Mounting and Component Holes

Details on drilling specific sized holes for mounting and components.

Painting the Model Body

Preparing the Body for Painting

Steps to wash and prepare the body surfaces before applying paint.

Spray Painting Techniques

Instructions for applying paint from the inside using spray cans.

Applying Markings and Stickers

Sticker Cutting and Application Guide

Step-by-step guide on how to cut and apply stickers accurately.

Using Tamiya Plastic Paints for Figures

Guidance on using Tamiya plastic paints for painting the driver figure.

Attaching Body Components

Installing Headlights and Lenses

Instructions for making and installing lights, including optional LEDs.

Mounting the Body to the Chassis

Steps for mounting the body onto the chassis using screws and washers.

Driver Figure Assembly and Mounting

Painting the Driver Figure

Guidance on painting the driver figure using plastic paints.

Attaching the Driver Figure to the Chassis

Instructions for attaching the assembled driver figure to the chassis.

Rear Body Mount Installation

Cutting Rubber Tubing for Mounts

Instructions for cutting rubber tubing to a specific length for mounts.

Attaching Rear Body Mounts

Steps for attaching the rear body mounts to the chassis.

Final Body Fitment and Antenna Routing

Trimming Body Posts

Instructions for trimming body posts to achieve desired fitment.

Routing the Antenna Wire

Guidance on routing the antenna wire through the designated pipe.