Tamiya RC Dual Rider User Manual

trDIJFIT- FIItrDEFI
trtr
)^lLl
TAMTEA
itVlbi,l9'-
aad),Äi 1
tl. r 3-o1./
+
-,
t fERT t*.t"
aThis
body can b€ us€d with lhe T3-ol
chassis.
TRIPI.C
WHE€L
A:*r
a
EO+,:/
ts lrgrri-<
=,
ttTt"
ß
öffi
ti
ä'r:r SrSE t t
lä* 4.ä E
a<r:t!r.
*,l.,J\+ääLOE+lä
Orä\ßrrträl3tl.
* itoä6
ä5Ear< ,:t1."
aTEo)EEt lr+r)*t Lt<
r:t
1."
l*tz=e
t \-1F+<
2tiZrrttzt-A,
,J{lttr.,*tL?<
r:tt."
a*1fl
rn!!f+tl.
{EH!.äniilizf,rä
tt@;ta*ttt<
*a. fi ;ritt{E
L<&ELz<,:tL\. 5t.
*E?aC
trtgFro
ttri+r*t Lz< r:- r\.
a,J\tä 157f§@u\
ärrffi r@I{tl*
L,liL\?< titLl! Il1t.t r,2frtr!
,l\ttl
§-Y0)üAr;^öt.
E:-r!S
tä'§?<@IEt ä€!ltdlirärti
ä'r*t"
i
)
('{
*'tE
bt A'fzitt
z<l:tlr"
A
caurrox
aBead
carelulv and tully undeßrand
the
instruclions
bofore commencing
awh€n
assembling this kit,
lools in-
cluding knives aß used. Extra
cärE
should be takeo to avoid
personal
iniury.
ORead
and follow th6 instructions
supplied with
paints
andlor cement, if
us€d
(not
included in kit).
aKe€p
out ol reach ol small
childr€n.
Chilclren
must
not be allow€d to
pur
any
parrs
in lheir moutß,
or
pull
viny|
bägs over th€ir heads.
Seßibly dis-
pose
ot th€
lsttovsr
parls
imm€diarev.
(fiiqr
ru.t):
Trimming

Tamiya RC Dual Rider Specifications

General

Scale	1/8
Drive Type	Rear-Wheel Drive
Length	260 mm
Motor Type	Brushed
Battery Type	7.2V NiMH Battery Pack
Required Battery	7.2V NiMH battery pack
Required Equipment	2-Channel Radio System, Battery Charger

Summary

Body Trimming

Masking and Painting

Preparing Body for Painting

Prepare the body by washing it with detergent to remove oil, then rinse and dry.

How to Paint

Apply masking stickers, then paint the body in stages following instructions.

Markings

Stickers

Cut out stickers carefully, peel backing slowly, and apply without bubbles.

Rider Marking

Attaching Body

Multipurpose Driver Figure Assembly

Driver Type

Assemble the driver figure, choosing the type that matches your model and painting it.

Rider Type

Assemble the rider figure, choosing the type that matches your model and painting it.

Rider Type Assembly Continuation

Attaching to Chassis

Attach the assembled rider figure to the chassis using double-sided tape, noting direction and angle.

Important Notices