Thankyou for
purchasing
the Tamiya Brushless ESC 04S
(Sensored).
This electronic
speed controller is designated lor use with motors of
15.5 turns
and above
in the
Tamiya Brushless Motor
(Sensored)
series, and also brushed motors 25 turns and
above.
I/lake sure to read the following safety
precautions
as breakage
and
accidents due to improper use
will void
yourwarranty.
*Always
follow instructions in
((1.High
Point Setup) to ensure
that
the high
point
setup is appropriate for
your
transm itter before use.
*lJsing
digital servos or those
with
current exceeding
1.5A may damage the ESC.
.Cc,NTFIG,LLEI
tTEtll45069
'I'I
)^l)^l
TAMTYA
Specifications
ESC: Forward
/
Brake/ Beverse
Max, continuous current:
754
lnput voltage: 6.6-7.2V
Output: Forward
-
100% Reverse-50%
Dimensions:41.5 x 33.4 x'18mm
Weight:479
Compatible
I!,1otors: Tamiya Brushless
Motors
(Sensored)
15.5 turns or over,
Sport-Tuned
motors, Tamiya brushed
motors 25 turns or over.
Receiver Output Voltage: 6V/'1.5A
FactorySettings
NeutralBrake: Setting
2
i5%)
Brake Output: Setting
10
(100%)
Rererse Function: Enabled
Battery Cut-Off:
Lo
Motor: Brushless IMotor Mode
7\
wanlruo
Payclose attention tothe following safety
precautions
as improper use can destroythe
product
and void
yourwarranty
or lead to
property
damage and
personal
injuries.
aThis
speed
controlleris intended for use with R/C modelsthat operate on
the
ground.
Do not use with othermodels.
(Dconnect
receiver to ESC and servos
securely. Connectors may become ioose due to
vibrations while
running.
aNeveroperate
any R/C modelin electrical storms.
aAvoid
running in rain or through surface
water. Water in the equipment may cause
aDisconnect
and remove battery
pack
when model
is not
being
used. lf left
connected
rhe modelmay
run
out otcontrol.
causing damage or injury.
aKeep
receiver, battery
pack
and model etc. out of reach of smallchildren.
I
crurtou
aMake
sure the
polarity
is correct when connecting
a battery
pack
and
motor to
prevent
damageto
ESC and receiver.
acontinuous
running may damage
battery connectors.
Battery
pack,
motorand ESC
become extremely hot during
or after operation and can cause
burns iftouched.
aNevershort
circuit batteryor
motorcables as
it may damagethe R/C unit.
aThis
speed controller
contains
precise
eleclronic equipment. Shocks,
impacts,
waterand
humidity are allpossible causes
ofdamage and should be avoided.
alDo
not disassemble or
modifythe ESC. This ESC is onlyfor usewith
Tamiya battery
packs
and motors. Use
ofotherproducts may damage
the R/C unit.
aNever
run an R/C modelon roads orstreets,
orin crowded areas.
aNever
connect to a brushed
motorwhen ESC is in brushless mode and
viceversa, as
this may damage
the ESC.
((Part
names)
((CAUTION)
*Always
turn on transmjtter
first, ihen receiver Alter use,
alwayslurn otf
rece
ver first, then
transmitter Failing to
do so
may
lead to the model runnino out 01
a
Receiver connector
*Connect
to 2
(CH.2)
on
a
Battery connector
XiorTamiya
Battery Pack
a
Sensor cable
n:cut off the tab when connectins
lo a SANWA or JR receiver.
Note
direction
and
polarity
when con-
a LED a Set
bulton
(
)Connection
(Brushless
motors)
Blue
=
XN4otor: Blue
Yellow
=*lMotor:Yellow
Orange
=
XMotor:Orange
.-rConnection
(Brushed
motors)
Blue
=
*Motor: Minus
(-)
Yellow
=
XMotor:
Plus
(+)
Orange
=
*Not
used.
ß
G
ON &§ OFF
rnm
I@el
::::--
-t
l--l
a
Beceiverswitch
(NOTTCE)
*Please
notethat
parls
such as ESC,
motor, bältery
pack,
and cablesemit noisedue
to large amounts oi electric cu
ent. Putling lhe receiver and anienna
near such
devices may lead
to interference causing
loss of control. The receiver and antenna
must noi
touch the ESC. The antenna
mLrst not cros§ overwith cables
irom the ESC.
Carbon
or metal chassis may
also transler inierference.
((Throttle
Operation and
LED lndicator»
aLED
remains
orf while
throtile irigger is in neutral
position.
andturns on when
vlgger is moved
rorwards
orbackwards.
When tr
gger
reaches full throttle or fu I
brake. LED turns off.
((Adjustinq
Settings»
The 2
procedures
lisled at righi
a.e used
to set up the various
*Connect
equipment as
shown above, and always
ensure the
modelcannot move
berore
adjusting settings, by
placing
it in a
position
where
wheels are
not in
contact
with
the
grcund,
remov ng the
*A
beep
tone is emitied if the
FullThrottle Fotuar.l
Beveße FullBeveße
Neutral
(Brake) (FullBEke)
A.
Hold down Set bulton
when
transmitter
and receiver
are alreadyturned
on.
aLED
lights up inthe order
Bed
J
Green
JOrange
-
Bed.
d
LED liqhts up Bed
+
Re ease Ser b-(Io.
ro.llcr
I
.t
1.
.rrq1 Point selup
I
LED lights up Green
,
Berease ser bul
rol
ro enra.
|
.l
2. Neun dl
Br
ake s'ruP
L
LED lights up orange,
Feledse
ser bullol
ro enra'
3
B'arS.luP
B. Switch on receiverwhile
holding down set button.
i
LED
lights
up
Bed
J
Beleas^ser oullolro
pnler
I
I
4' RFversasarup
I
LED
lig'lts
up Green
,
Release Sal
burtor to e_ter
I
J
5'
Bä e'YcuFo'rseru'
L-
LED lishts up Orange.)
BeleaseSer ouxon ro enre,
i(6. Molor Mode Setup)
o
'ii-A
o
,R-->
itt
e
LEDoff
LEDon
'LEDofl' LEDon
LLDoh
To Next Page
Loading...
Need help?
General
