EasyManua.ls Logo

Tandberg Data StorageLibrary T40 T40 - User Manual

Tandberg Data StorageLibrary T40 T40
95 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation and User Guide

Table of Contents

Questions and Answers

  • B
    braunnatalieSep 18, 2025
    What causes Tandberg Data StorageLibrary T40 T40 Storage to fail to fetch at slot n?
    • T
      Tara PerrySep 18, 2025
      If your Tandberg Data Storage failed to fetch at slot n, reboot the loader and retry the operation. Remove the magazine if possible. Remove all cartridges. Verify that the cartridge is not damaged. Insert empty magazines. Power cycle the loader. Retry the operation. Retry the operation with a new magazine. This issue arises when the robotics cannot fetch the requested cartridge from the magazine.
  • J
    Jeffrey GrantAug 25, 2025
    What to do if Tandberg Data StorageLibrary T40 T40 shows 'Drive n Tape Alert 9. Write Protect'?
    • K
      Kevin McconnellAug 25, 2025
      If you receive a 'Drive n Tape Alert 9. Write Protect' error with your Tandberg Data Storage, it means you're trying to write to a write-protected cartridge. To resolve this, remove the write-protection or use another tape. This alert appears because you are trying to write to a write-protected cartridge.
  • M
    Mr. Christopher GreenAug 25, 2025
    Why does Tandberg Data StorageLibrary T40 T40 show 'Drive n Tape Alert 4. Media'?
    • M
      mariewarrenAug 26, 2025
      If your Tandberg Data Storage shows 'Drive n Tape Alert 4. Media', your data is at risk. Copy any data you require from this tape, and do not use this tape again. Restart the operation with a different tape. This alert indicates an error occurred while reading or writing data.
  • R
    richard26Aug 27, 2025
    What causes 'Drive n Tape Alert 5. Read Failure' in Tandberg Data StorageLibrary T40 T40?
    • L
      lucas39Aug 27, 2025
      If your Tandberg Data Storage is displaying the error 'Drive n Tape Alert 5. Read Failure', try cleaning the drive. If that doesn't work, try another cartridge. If the problem persists, the tape drive may need to be replaced. This issue can occur if the tape is damaged or the drive is faulty.
  • B
    Brian WilkinsonSep 18, 2025
    What to do if Tandberg Data StorageLibrary T40 T40 Storage failed moving the robotics?
    • J
      jennifer91Sep 18, 2025
      If your Tandberg Data Storage failed to move the robotics, reboot the loader and retry the operation. This problem happens when the robotics was not able to move.
  • R
    Robert CarterSep 23, 2025
    How to fix Tandberg Data StorageLibrary T40 T40 Storage when Diagnostic number ZZ failed?
    • J
      Jeffrey ChavezSep 23, 2025
      Reboot the loader and retry the operation.
  • D
    Daniel HenrySep 9, 2025
    What does 'Drive n Tape Alert 32. Interface' mean on Tandberg Data StorageLibrary T40 T40?
    • M
      manningtammySep 9, 2025
      If your Tandberg Data Storage displays 'Drive n Tape Alert 32. Interface', check the cables and cable connections, and then restart the operation. This alert indicates a problem with the host interface.
  • P
    pleeSep 10, 2025
    How to resolve Tandberg Data StorageLibrary T40 T40 Storage 'Drive n Tape Alert 30. Hardware A'?
    • N
      Nancy BrownSep 10, 2025
      If your Tandberg Data Storage displays 'Drive n Tape Alert 30. Hardware A', eject the tape, reset the drive, and restart the operation. This alert indicates the tape drive has a hardware fault.
  • M
    monica19Sep 3, 2025
    Why won't my Tandberg Data StorageLibrary T40 T40 Storage Library take inventory?
    • S
      Susan HuangSep 3, 2025
      If your Tandberg Data Storage library does not take inventory, make sure the transport screws are removed and that all magazines are in their locked position.
  • R
    Riley MosleySep 1, 2025
    How to fix a dead display on Tandberg Data Storage?
    • J
      Johnny SchultzSep 1, 2025
      If your Tandberg Data Storage library display is dead, power cycle the library by turning it off and on using the main power switch on the rear. Check that the fans start at power on and then stop after a few seconds. Also, check the power cord connection and ensure the power switch on the rear panel is in the ON position. Make sure there is power to the outlet, and try another working outlet. Replace the power cord if necessary. Check the fuse located beside the power connector on the rear panel and replace it if blown (a spare fuse is located behind the fuse door). Verify that the power supply unit is properly inserted into the bay. Replace the power supply unit.

Summary

StorageLibrary T40 Installation and User Guide

Document Overview

Introduces the StorageLibrary T40 and the purpose of this installation and user guide.

About This Guide

Guide Basics and Resources

Covers guide purpose, symbols, related documents, and support contact information.

Product Overview

Library Components and Features Overview

Describes physical components, interfaces, and key features of the StorageLibrary T40.

Information about the Operator Interfaces

Operator Interface Navigation

Explains how to use the Front Panel and Remote Management interfaces for library operations.

Configuring the Library

Setup Wizard and Configuration Options

Guides users through initial setup and details available configuration tasks and options.

Running the Library

Library Access and Cartridge Management

Explains login procedures and cartridge import/export operations for library use.

Getting Status and Information

Viewing Library and System Status

How to access reports for library settings, drive configurations, network, and statistics.

Adding, Removing and Replacing Hardware

Hardware Component Procedures

Covers power supply unit and tape drive unit management procedures.

Updating Firmware

Firmware Update Procedures

Details updating library and tape drive firmware for optimal performance.

Working With Cartridges and Barcodes

Cartridge Handling and Barcode Requirements

Best practices for cartridge handling and barcode labeling requirements.

Troubleshooting Library Issues

RAS Tickets and Error Resolution

Introduces RAS tickets for library issues and how to resolve them using supported tickets and LEDs.

Shipping or Transporting StorageLibrary

Preparation for Movement and Shipment

Covers reinserting transport screws and packing the library for safe transport.

Specifications and Dimensions

Library Specifications and Component Details

Provides library specs, dimensions, component weights, power, and environmental data.

Safety and Regulatory Information

Safety Approvals and Regulatory Compliance

Lists safety certifications, EMC standards, and regulatory declarations for the product.

Approved Drive Types

Compatible Tape Drive Models

Lists the approved IBM LTO drive models (SCSI and Fibre Channel) for the StorageLibrary T40.

Tandberg Data StorageLibrary T40 T40 Specifications

General IconGeneral
ModelTandberg Data StorageLibrary T40
TypeTape Library
Number of Slots40
Drive SlotsUp to 2
Tape Slots40
InterfaceSAS
Max Tape Capacity800 TB (with LTO-8 tapes)
Power Consumption150 W (operating)

Related product manuals