Tarrington House K103M1BME3-1

Questions and Answers

N
Noah RuizAug 13, 2025
Why is my Tarrington House Grill not getting hot enough?
- M
  Michael PalmerAug 13, 2025
  If your Tarrington House Grill only heats up from 100 °C to 150 °C, even with the knob in the HI position, there are several potential solutions: * First, ensure the thermometer is functioning correctly by comparing its reading to that of an oven thermometer placed inside the grill. * Next, check all gas connections for leaks and tighten them if necessary. * Straighten any bends or kinks in the gas hose. * Clear any blockages in the burners or orifice. * Have your gas dealer inspect the gas cylinder for low pressure. * Finally, if the gas supply is insufficient, refill or replace the gas cylinder.
J
James RodriguezAug 17, 2025
How to fix Tarrington House K103M1BME3-1 that won't ignite right away?
- J
  Jose WilsonAug 17, 2025
  If your Tarrington House Grill does not ignite immediately, try the following: * Make sure that the gas valves are open. * Check if sparks are produced when igniting the appliance. * Push the control knob for 5 seconds before you try to ignite the appliance. * Ensure that the burners are clean. * Check if the gas cylinder is not empty.
J
James DuffyAug 20, 2025
Why does my Tarrington House K103M1BME3-1 Grill take so long to heat up?
- T
  Tonya DavenportAug 20, 2025
  If your Tarrington House Grill takes a long time to heat up, it could be due to a few reasons. When it is cold outside, the appliance will naturally take longer to heat up; typically, it takes about 10-15 minutes to heat from 250°C to 320°C. Also, check if the gas supply is sufficient by refilling or replacing the gas cylinder. Lastly, ensure that the gas hose is not blocked or clogged.
J
Joshua HickmanAug 25, 2025
What to do if my Tarrington House Grill won't ignite?
- C
  Christopher WilliamsAug 25, 2025
  If your Tarrington House Grill does not ignite at all, it could be due to a few reasons. If the electrode does not aim at the burner hole, align them and adjust the distance between the metal pin of the electrode and burner hole to 3-5 mm. Also, check for any obstructions in the burners, gas jets, or hose, and clean them as necessary.
F
Frank JamesAug 28, 2025
How to stop flare-ups on my Tarrington House K103M1BME3-1?
- J
  Justin Jackson DDSAug 28, 2025
  If you experience a flare-up of the burner flame on your Tarrington House Grill, it might be due to excessive fat content in the meat. Remove part of the fat before grilling. You can also reduce the temperature, and clean any grease deposits you spot.
W
weberrebeccaAug 31, 2025
Why is the pressure regulator on my Tarrington House K103M1BME3-1 making noise?
- J
  Jenny NguyenAug 31, 2025
  If you hear noise from the pressure regulator of your Tarrington House Grill, it might be because the ventilation opening on the pressure regulator is plugged. Unplug the opening and wait 5 minutes before starting again. Also, check if the ventilation openings are covered up, and remove any obstructions.
P
Peter RamosSep 4, 2025
Why is there no spark when I try to ignite my Tarrington House K103M1BME3-1?
- T
  Timothy WelchSep 5, 2025
  If there is no spark noise when trying to ignite your Tarrington House Grill, check if the wire between the metal pin and igniter is off and connect the wire. Also, ensure that the electrode aims at the burner hole; align them and adjust the distance between the metal pin of the electrode and burner hole to 3-5 mm.
J
Jeffrey CordovaSep 8, 2025
Why is the flame on my Tarrington House Grill not blue?
- E
  Erin VaughnSep 8, 2025
  If the burner flame on your Tarrington House Grill is not blue, check if there is too much or too little air being supplied. Also, check if the burner is misaligned. In case of incomplete combustion, it is recommended to contact a specialist.