TATA Motors nano emax User Manual (English)

Questions and Answers:

T
Thomas MartinAug 25, 2025
Why is there abnormal or excessive tyre wear on my TATA Motors Automobile?
- C
  cparkerAug 25, 2025
  If you observe abnormal or excessive tyre wear on your TATA Motors Automobile, check the tyre balance and adjust if required. Also, adjust the steering geometry and ensure tyres are adequately inflated. If you notice a wobbly wheel or tyre, or a defective tyre, consider replacing them. Other potential causes include improper hub play (replace the bearing), brake grabbing (check and rectify), and excessive braking (modify driving habits).
M
Mark SullivanAug 25, 2025
What to do if TATA Motors Automobile engine cranks but does not start in Petrol Mode?
- T
  Taylor TranAug 26, 2025
  If the engine of your TATA Motors Automobile cranks but doesn't start in petrol mode, it could be due to air in the fuel system, which needs rectification. Check for leakages and correct them. Also, inspect the fuel pump or EMS fuse and replace it if blown. Ensure you have enough fuel and replace the fuel filter if it's clogged.
J
James PriceAug 26, 2025
Why is the charging indicator continuously ON in my TATA Motors Automobile?
- B
  Billy ScottAug 26, 2025
  If your TATA Motors Automobile's charging indicator continuously remains ON, it could be that the battery is not getting charged due to a loose belt. In this case, get the belt tension adjusted or replaced if broken. Another reason may be a loose alternator terminal, so tighten the charging terminal. If the alternator is not working, get it rectified or replaced.
T
Tony Miller MDAug 27, 2025
How to troubleshoot a blower motor that doesn't operate in a TATA Motors nano emax?
- S
  Sara McdonaldAug 27, 2025
  If the blower motor in your TATA Motors Automobile does not operate, start by replacing the fuse and correcting any disconnection in wiring. Ensure all connections are secure. If the motor is faulty, replace it. Also, check for faulty connections and replace the resistor block if defective. Lastly, replace the fan switch if it is faulty.
M
michellemccartySep 9, 2025
Why is my TATA Motors nano emax clutch noisy?
- M
  Maria HillSep 9, 2025
  If you hear a noisy clutch in your TATA Motors Automobile, it could be due to pressure plate and diaphragm spring rattling. In this case, get your car attended by an authorized Service outlet.
L
lindamooreSep 7, 2025
Why does the suspension of my TATA Motors nano emax bottom out?
- C
  Cindy PrattSep 7, 2025
  If your TATA Motors Automobile suspension bottoms out, it could be due to overloading, so check the loading. Another possible reason is faulty struts, which should be replaced.
J
jdavisSep 8, 2025
What causes poor return ability in TATA Motors nano emax steering?
- A
  Amy RothSep 8, 2025
  If you notice poor return ability in your TATA Motors Automobile's steering, check for grabbing of linkages and rectify it. Also, inspect the steering gear for any disturbance and adjust it accordingly.
R
Richard SmithSep 2, 2025
Why does my TATA Motors nano emax not accelerate?
- W
  William CooperSep 2, 2025
  If your TATA Motors Automobile does not accelerate, it could be due to a broken accelerator cable, which needs replacement. Another possible cause is a choked fuel filter, which should also be replaced.
Z
Zachary PadillaAug 31, 2025
Why is the clutch slipping in my TATA Motors Automobile?
- R
  Robert Wood Jr.Aug 31, 2025
  If your TATA Motors Automobile experiences clutch slipping, adjust the pedal travel if it's improper. If the clutch cable is rusted, replace it. If there is oil on the clutch disc, clean or replace the disc at an Authorized Service outlet.
M
Matthew JohnstonSep 1, 2025
What causes abnormal noise from the front end of my TATA Motors nano emax Automobile?
- B
  Brandy CampbellSep 1, 2025
  If you notice an abnormal noise from the front end of your TATA Motors Automobile, it could be due to damaged struts or mounting, which should be repaired. Worn suspension arm bushings should be replaced. Ensure that the wheel bolts and suspension bolts or nuts are tightened. Excessive hub play requires bearing replacement.