Why is my Taylor McDonald's R200 showing 'Cooling Failed (Error 6)'?
If the Taylor Dispenser displays 'Cooling Failed (Error 6)', start by cleaning the condenser and filter. Also, ensure the ambient temperature is below 90°F. A power outage can also trigger this error, so check for that as well.
Why is the cooling slow on my Taylor McDonald's R200 showing 'Error 5'?
If your Taylor Dispenser is showing 'Cooling Slow (Error 5)', start by cleaning the condenser and filter. Make sure the cabinet door is fully closed. Also, check the refrigerant level and confirm that the compressor and condenser fan are working properly.
How to fix a Taylor McDonald's R200 Dispenser when the drum won’t turn and shows 'Error 1'?
If the drum of your Taylor Dispenser won’t turn and shows 'Error 1', check that the drum motor connectors are securely connected both at the drum motor and on the main controller. Verify power is present at the motor. You can also use the Drum parameter in the Test Outputs section of the Service Menu to manually operate the drum motor.
What to do if my Taylor Dispenser has a weighing issue and displays 'Error 4'?
If your Taylor Dispenser shows 'Weighing Issue (Error 4)', first verify the proper installation of the accumulator housing, hopper, and flap door. Use the Accum parameter in the Test Outputs section of the Service menu to manually operate the accumulator motor and doors. Check for any fries interfering with the accumulator door shafts.
What to do if the Fry Door Failed on my Taylor McDonald's R200 and it shows 'Error 3'?
If your Taylor Dispenser displays 'Fry Door Failed (Error 3)', check for any obstructions that might be restricting the accumulator door movement. Remove the upper back panel and disconnect, then reconnect the accumulator home switch connector at the controller. You can also use the Accum parameter in the Test Outputs section of the Service menu to manually operate the accumulator motor.
What causes Fry Doors to get stuck on a Taylor McDonald's R200 Dispenser ('Error 2') and how can I fix it?
If your Taylor Dispenser displays 'Fry Doors Stuck (Error 2)', check for any obstructions that might be interfering with the accumulator door movement. You can also use the Accum parameter in the Test Outputs section of the Service menu to manually operate the accumulator motor.
What does 'Refrig. Error (Error 7)' mean on my Taylor Dispenser, and how do I resolve it?
If your Taylor Dispenser is showing 'Refrig. Error (Error 7)', verify that there are no wiring problems first, then replace the feedback (SW3) and refrigeration (SW2) relays.
How do I fix a 'Probe Failure (Error 8)' error on my Taylor Dispenser?
If your Taylor Dispenser displays 'Probe Failure (Error 8)', replace the temperature probe.
What should I do if my Taylor McDonald's R200 Dispenser shows 'DC Power Low'?
If your Taylor Dispenser shows 'DC Power Low', cycle the power and check the supply voltage.
What does 'NV Data Lost' mean on my Taylor McDonald's R200 Dispenser and how do I fix it?
If your Taylor Dispenser displays 'NV Data Lost', press the OK button or cycle the power.
Step-by-step guide for unpacking and setting up the dispenser for operation.
Details electrical, physical, operational, and refrigeration parameters of the dispenser.
Essential safety rules to prevent injury and machine damage during operation and maintenance.
Critical warnings on grounding, power, and safe installation practices.
Guidelines for safe operation, handling hot parts, and preventing obstructions.
Step-by-step instructions for assembling the dispenser components.
Steps for powering on and preparing the dispenser for initial product dispensing.
Guide to dispensing, hopper loading techniques, and setup.
Procedures for taking apart, defrosting, and cleaning the dispenser.
Identifies error codes and provides detailed steps for diagnosing and resolving issues.
Explains system operation, required maintenance, and cleaning of critical components.
Overview of menu navigation, configurations, and scale calibration procedures.
Visual schematics for the refrigeration circuit and electrical wiring.
Details warranty terms, conditions, and exclusions for the dispenser and replacement parts.
To Next Page
General