Teac WX Navi - User Manual

Questions and Answers

D
Dana GarciaAug 17, 2025
What to do if the Teac WX Navi Voice Recorder shows 'Inserted media is not supported'?
- J
  johnsonmichelleAug 17, 2025
  If your Teac Voice Recorder displays the message 'Inserted media is not supported', the problem may be due to several reasons. First, ensure that the media you are using is compatible with the WX-7000. Second, check whether the media has been formatted by the WX-7000. When formatting media for the first time, format it using the WX unit. Finally, verify that you are using media that has been confirmed to work with the WX-7000.
E
Edward PatelAug 20, 2025
Why WX Navi does not recognize the Teac Data Loggers WX-7000?
- C
  Christopher StephensonAug 20, 2025
  If WX Navi isn't recognizing your Teac Data Loggers WX-7000, check these things: * Make sure the LAN cables are properly connected. * Verify that the IP address and subnet mask settings are correctly configured. * Ensure that the computer’s firewall isn't blocking it. * Try turning the WX-7000 power off and on again, then restart WX Navi.
D
Debra VillaAug 22, 2025
What to do if main unit buttons do not function on Teac Data Loggers?
- E
  Erica BrownAug 22, 2025
  If the buttons on your Teac Data Loggers unit aren't working, here are a couple of things to check: * See if the panel is locked; if it is, unlock it. * Note that the buttons are disabled during WX-Navi operation. After interrupting transmission with WX-Navi, button use will be possible again after at least 3 minutes.
I
iturnerAug 25, 2025
What to do if “Inserted media is not supported” message appears on Teac Data Loggers?
- D
  Donna RodriguezAug 26, 2025
  If you're getting an “Inserted media is not supported” message on your Teac Data Loggers, consider the following: * Confirm that compatible media is loaded. * Check if the media has been formatted by the WX-7000. If not, use the WX-7000 to format it. * When formatting media for the first time, format it using the WX unit. * Verify that you are using media that has been confirmed to work with the WX-7000.
D
Dawn PorterAug 27, 2025
How to fix Teac Data Loggers if power will not turn on?
- S
  Scott AyalaAug 28, 2025
  If your Teac Data Loggers power won't turn on, check if the power adapter is connected and that the DC power supply voltage isn't too low.
B
burgesskatherineAug 30, 2025
Why cannot select the sampling frequency on Teac Data Loggers?
- M
  michaelblackAug 30, 2025
  If you cannot select the sampling frequency on your Teac Data Loggers, ensure that the number of channels is not set to more than what the recording media supports.
M
Michaela WardSep 1, 2025
What to do if RDX cartridge not recognized on Teac Data Loggers?
- J
  Jason BrooksSep 1, 2025
  If the RDX cartridge is not recognized immediately after insertion in your Teac Data Loggers, turn the WX-7000’s power off and then on again.
C
Christopher ThompsonSep 4, 2025
How to fix Teac WX Navi if power will not turn on?
- V
  Veronica MorrisSep 4, 2025
  If your Teac Voice Recorder is not turning on, there are a couple of things to check. First, make sure the power adapter is properly connected. Second, verify that the DC power supply voltage is appropriate.
T
Tracie NavarroSep 6, 2025
Why WX Navi does not recognize the Teac Voice Recorder WX-7000?
- K
  Kenneth VazquezSep 6, 2025
  If WX Navi is not recognizing the WX-7000 Teac Voice Recorder, consider these potential causes: * Ensure the LAN cables are correctly connected. * Verify the IP address and subnet mask settings are correct. * Check if the computer’s firewall is blocking the device. Additionally, try turning the WX-7000 power supply off and on again, then restart WX Navi.
S
Stephanie GarciaSep 8, 2025
What to do if Teac WX Navi Voice Recorder main unit buttons do not function?
- D
  Dennis HodgeSep 9, 2025
  If the main unit buttons on your Teac Voice Recorder are not functioning, first check if the panel is locked and unlock it. Also, note that the buttons are disabled during WX-Navi operation; after interrupting transmission with WX-Navi, button use will be possible again after at least 3 minutes.