To Next PageTo Next Page
Need help?Do you have a question about the Team Blacksheep TBS TANGO 2 Radio and is the answer not in the manual?
Identifies key controls and features of the radio via diagrams.
Close-ups of buttons, display, and ports.
Visuals of gimbals and switch types.
Instructions for powering on and using the USB joystick mode.
Guidance on SD card content and formatting.
Explains the functions of Menu, Page, Exit, and Enter buttons.
How to use sticks and the rocker for menu navigation.
Step-by-step guide to change the default stick mode.
How to configure mixing and endpoints for flying wings.
Accessing LUA tools like Agent Lite and Crossfire menu.
Navigating and updating SD card contents.
Configuring date, time, sound, volume, and feedback settings.
Setting up battery low, inactivity, and other audible alerts.
Configuring splash screen, delays, time zone, and units.
Configuring channel order and stick-to-control mapping.
Using switches for special functions across planes.
Procedures for calibrating sticks and configuring switches.
Performing battery calibration and checking RTC battery voltage.
Information about the current firmware build and options.
Detailed instructions on how to re-perform gimbal stick calibration.
Performing model actions, viewing metrics, and managing models/categories.
Steps for selecting, creating, duplicating, and deleting models.
Choosing the aircraft type for a new model.
Assigning throttle channel and control surfaces.
Configuring general OpenTX features like model name and timers.
Adjusting travel limits, trims, and reverse settings.
Configuring throttle source and preflight warnings.
Settings for center beep, external RF modules, and model matching.
Creating and configuring flight mode slots for different flight characteristics.
Setting up input formatting rules for each stick axis.
Mapping controls to servos and configuring output channels.
Using custom curves in input formatting or mixers.
Creating logic switches for comparing conditions.
Triggering special functions using switches.
Selecting and configuring LUA scripts for complex mixes.
Configuring RSSI indicator and detailed sensor information.
Setting up variometer tones and sensor discovery.
Configuring telemetry view screens for display.
Instructions for attaching a neck strap.
Simple steps to bind a CROSSFIRE receiver using Agent Lite.
Setting up Model ID for binding to specific receivers.
Configuring CROSSFIRE failsafe states via Agent Lite.
Configuring warnings for switch positions.
Points to the CROSSFIRE manual for detailed functions.
Explains the meaning of different LED patterns.
How to easily adjust stick trims while in use.
Details on battery protection based on voltage levels.
Events that cause the remote to raise an alert.
Steps to remove rubber covers and screws to open the radio.
How to remove and install the internal battery.
Modifying the throttle stick to be non-sprung.
Adjusting the smoothness or clicking of the throttle stick.
Modifying the tension of the gimbal springs.
Modifying the travel limits of elevator and throttle sticks.
Procedure for removing mainboard and gimbals.
Replacing softer springs for a smoother response.
Detailed steps and a trick for installing gimbal springs.
Steps to swap the antenna for an external SMA connector.
Configuring WiFi client, SSID, password, and network connections.
Configuring MAVLink streams and enabling/disabling Web UI.
Settings for WiFi power and CLOUD connection.
Steps to download firmware and update the WiFi module.
Connecting the radio to an external WiFi hotspot via Web-UI.
Alternative method to connect via Agent X/M/Lite.
Downloading and using Agent X for firmware updates.
Steps to back up SD card contents to a PC.
Procedure for updating the FreedomTX firmware.
Steps to update the CROSSFIRE module firmware.
Downloading and copying correct content to the SD card.
Specific steps for updating from older FreedomTX versions.
Requirements for FreedomTX and CROSSFIRE firmware compatibility.
Bypassing OpenTX mixer settings for faster response.
Setting up audio warnings for Link Quality (LQ) sensor.
Making momentary switches behave like sticky ones.
Using a button to set trim values based on stick position.
Guide to identifying different PCB versions (V1-V4).
Steps to install a mini-module bay add-on.
Troubleshooting common binding and signal loss problems.
Resolving issues with switches not working or limited frequency settings.
Fixing issues where CROSSFIRE/WiFi modules don't show up.
General| Frequency | 2.4 GHz |
|---|---|
| Channels | 16 |
| Radio Firmware | OpenTX |
| Display | Color LCD |
| RF Power | 100 mW |
| Charging Port | USB-C |
| Gimbals | Hall sensor |
| Modulation | TBS Crossfire |
| Compatibility | Crossfire |
| Battery | 18650 Li-ion (2 cells) |
