Technics SL-PC25

li PLAYING A DISC
| Continuous play {from the stop mode)
Continuous play refers to play of the first track of the first disc to the last
track of the last disc.
2 Open the dust
cover.
3 Load disc(s) on
the disc tray(s).
1 Press the power switch to turn on (M_. =).
The disc trays turn clockwise, and the disc 1 tray resets to the
front position
Continuous play is automatically selected when the power is
switched on. If the program play indicator is illuminated,
press the program/continue button
Disc indicators
al LILI
track
| <> <ap aap <a ae! 7) 7) i ms a i |
|
H i
Nh
Open the dust cover.
wo
Load the disc(s) on the disc tray(s).
®Continuous play begins from disc 1 when the play button is
pressed.
¢For loading disc 5, press the disc skip button or turn the disc
trays manually.
Notes:
*Do not touch the disc tray while rotating.
*During play, other discs can be changed.
¢Discs of the 8 cm (3”) size and 12 cm (5") size cannot be used
together on the same number disc tray.
The disc skip button cannot be used during program play.
if intermittent noises are produced while the carousel is rotating,
this means that the lock shaft is not released. Set the power
switch to off and release the shaft according to the procedure on
page 2.
program/
continue
pause
4 Press the play button to start play.
The play indicator will illuminate and continuous play will start.
The indicator corresponding
to the disc being played flashes.
SE BN ARE ee ! mer
7s t tee tnt
wack min tor
Play indicator
At the end of the last track of the last disc, the unit switches to
the stop mode
To briefly interrupt play
Press the pause button.
The unit switches to the pause mode and the pause indicator
illuminates.
Press the play button to resume play.
Pause mode:
Play is stopped, but the pickup remains where it was at the
time when the pause button was pressed. The disc rotates
while the unit is in the pause mode.
To stop play
Press the stop button.
Stop mode:
in the stop mode the pickup is at its rest position; the disc
does not rotate, and the display will show all zeros.
Continuous play continues
G29d° 1S
To select the desired track (or disc) to be played (trom the stop mode or during play)
By selecting the disc or track to be played first in the play
sequence, al! subsequent tracks will be played on that disc(s) in
order from that track to last. (There is no need to press the play
button.)
1 Press the disc select button.
If the disc only is selected, play of ati tracks on that disc
(beginning from its first track) will begin in about ten seconds.
For example: To select the 3rd disc, press the [3 ] button
The selected disc indicator will flash
2 Press the skip ([=1]) button to select the
track number.
Play will start from the selected track
For example: To select the 9th track, press the (-=1} button
8 times (or keep pressing the button until the
display shows “ 9").
Track number
If you go past the desired track, press the [=] button to
return to the desired track.
disc
a
2 Numeric buttons
e
3 Numeric buttons
@ By the remote control transmitter
(See page 7.)
1 Press the disc button.
2 Press the numeric button ((1)}-(5]) to specify
the disc.
3 Press the numeric button to specify the track.
Play will start from the selected track
To select the 10th and subsequent tracks
Press the [+10 button to select the “tens” digit, and then
press (one of) the [6}-{9] buttons to select the “units” digit
Example: to select the 32nd track
Press the(~10|button three times to select 3, and then press
the [2] button.
eSteps 1 and 2 are not necessary if the track is specified on
the 1st disc.
Notes:
elf a disc number not on the disc tray is specified, the next higher
number disc will be played.
When a track number not on the disc is specified, the selection
cannot be entered.