Technics SL-PJ28 - Page 3

MILOCATION OF CONTROLS
Control section
@ Power “STANDBY (5/ON” switch
(POWER STANDBY (4 /ON)
This switch switches ON and OFF the secondary circuit power
only. The unit is in the “standby” condition when this switch is
set to the STANDBY (4 position. Regardless of the switch
setting, the primary circuit is always “live” as long as the
power cord is connected to an electrical outlet.
@) Disc holder
@) Search buttons (<< SEARCH PP)
These buttons can be used to move rapidly forward or
backward on the disc during play. The search speed is slow
when the button is pressed at first and becomes faster if the
button is pressed and held continuously.
@ Repeat play button (REPEAT)
© Program button (PROGRAM)
Prassing this button initiates the program play mode. You can
‘then enter specific tracks using the skip buttons.
© Skip buttons (44 SKIP PPL) ©
These buttons can be used to skip tracks and to specify the
_track number or the desired recording time. . by pes eS
@) Play button (> PLAY)
Pause button (1! PAUSE)
@) Stop button (™ STOP)
This button can be used to stop the disc piay, as weil as to
cancel the various play modes.
@ Disc holder open/close button
(4 OPEN/CLOSE)
@ Random play button (RANDOM)
This button can be used to play the tracks on a disc in a
random sequence.
@ Tape side select button (SIDE A/B)
When recording compact discs to tape, this button is used to
switch the tape side for addition or cancelation of program-
—... Med tracks.
@ Edit mode button (NORMAL, TAPE LENGTH)
This button can be used to choose one of the edit modes or to
specify the tape length to be used. — '
Taye [fer-} Colac ect=tet tfola)
Link Indicator (LINK)
@) Edit indicator ({EDIT))
@® Multi-display
_
This
display
shows
the
track
number
and
elapsed
play
time
of
the current track, or the remaining time of the tape while the
unit is in the CD-edit mode.
@ Program indicator (PROGRAM)
Random play indicator (RANDOM)
Program cancel indicator (CANCEL)
Muminatee when the proorammed track can be cancelled. _
(It can be operated only by the remote control transmitter
included in the Technics tuner ST-X902.)
@) Play indicator ([>)
@) Pause indicator (51)
@ Repeat play indicator ( ¢> )
@ “Over” mark (BY ~~
This indicator tights if the total number of tracks on the disc is
17 or more. / a
@ Track number indicator ( 7 -% )
@) Tape side indicator (> A, > B)
@ Peak search indicator (PEAK SEARCH)
@ Fade end indicator (FADE END)
iluminates when the unit is normal! edit mode.
Mi HANDLING PRECAUTIONS FOR TRAVERSE DECK
The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static
electricity of clothes or human body.
So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
* Handling of traverse deck (optical pickup)
1. Do not subject the traverse deck (optical pickup)
to static electricity as it is extremely sensitive to
electrical shock.
2. To prevent the breakdown of the laser diode, an
antistatic shorting pin is inserted Into the flexible
board (FPC board).
When removing or connecting the short pin, finish
the job in as short time as possible.
3. Take care not to apply excessive stress to the
flexible board (FPC board).
4. Do not turn the variable resistor (laser power
adjustment). It has already been adjusted.
© Grounding for electrostatic breakdown
prevention
1. Human body grounding
Use the anti-static wrist strap to discharge the
static electricity from your body.
2. Work table grounding
Put a conductive material (sheet) or steel sheet on
the area where the optical pickup is placed, and
ground the sheet.
Caution:
The static electricity of your clothes will not be
grounded through the wrist strap. So, take care not
to let your clothes touch the traverse deck (optical
pickup).
Variable resistor
(Do not turn) - ~ 1
Optical pickup
Lens
(Do not touch)
FPC board
(Handle it carefully) [x
1MQ
in plate or some metals
to conduct electricity