To Next PageTo Next Page
Need help?Do you have a question about the Techno Line WT538 and is the answer not in the manual?
General| Type | Digital table clock |
|---|---|
| Calendar | Yes |
| Form factor | Rectangular |
| Product color | Gray |
| Projection function | Time |
| Display type | - |
| Battery type | AAA Micro LR03 |
| Number of batteries supported | 2 |
| Quantity per pack | 1 pc(s) |
| Batteries included | No |
Weight and Dimensions| Depth | 42 mm |
|---|---|
| Width | 147 mm |
| Height | 92 mm |
Lists various environmental and proximity factors that can interfere with wireless time signal reception.
Interference caused by natural landscapes like mountains and valleys.
Signal disruption from proximity to transport hubs and power lines.
Signal obstruction by tall buildings and concrete structures.
Interference from nearby electrical devices and metallic objects.
Challenges with signal reception while inside moving vehicles.
Specifies that the device is intended solely for indoor use.
Warning against subjecting the unit to excessive force or impact.
Advice to avoid extreme temperatures, sunlight, dust, and humidity.
Prohibition against immersing the device in water.
Warning to prevent contact with corrosive materials.
Safety instruction not to dispose of the unit in fire due to explosion risk.
Use only alkaline batteries and install them with correct polarity.
Always replace the full set and avoid mixing new and used batteries.
Remove exhausted batteries promptly and store safely away from metal objects.
Avoid exposing batteries to heat, humidity, direct sunlight, and keep from children.
Do not recharge, dispose of batteries in fire, or keep near children.
Symbol indicates separate disposal of electrical devices from household waste.
Instructions to take the unit to a local waste collection or recycling centre.
Details of icons and information displayed on the LCD screen.
Description of buttons and the DC adapter jack on the device's back.
Description of the touch-sensitive button on the top of the unit.
Utilizes DCF-77 radio signal for accurate timekeeping.
Supports both 12-hour and 24-hour time display formats.
Allows users to set the time zone with a +/- 12 hour offset.
Procedure for manually adjusting the clock's time.
Enables the time to be projected onto a surface.
Shows date and weekday in up to 7 languages.
Option to display temperature in Celsius (°C) or Fahrenheit (°F).
Integrated alarm with automatic snooze functionality.
Specifies the range for indoor temperature measurement: -9.9°C to 49.9°C.
Device can be powered by DC adapter or 2x AAA batteries.
Instructions for connecting the power supply or inserting batteries.
Guidance on inserting batteries with correct polarity.
Description of display activation, beep, and temperature detection upon startup.
Device automatically enters radio-controlled time signal reception.
Backlight and projection activate for 8 seconds via SNOOZE/LIGHT button.
WAVE button adjusts brightness; projection works unless switch is OFF.
The projection distance is approximately 2 meters.
Projection function is temporarily disabled during radio signal reception.
Clock automatically searches for DCF signal upon restart or battery change.
Automatic synchronization at 1:00, 2:00, 3:00 AM to correct time deviations.
If sync fails, it retries hourly up to 5 times.
Initiate DCF signal reception by pressing and holding the WAVE button.
Press the WAVE button once to stop radio signal searching.
Flashing icon indicates search start; continuous icon indicates successful reception.
Maintain a minimum 2.5m distance from interference sources like TVs/monitors.
Press and hold SET for 2 seconds to start 12/24 hour mode setting.
Adjust time zone from -12 to +12 hours using +/- buttons.
Use SET to cycle through and +/- to adjust hour and minute.
Choose between Month/Date or Date/Month display.
Adjust year and month using SET and +/- buttons.
Adjust the day of the month using SET and +/- buttons.
Select display language for weekdays from a list of 7 languages.
Automatic exit to Normal Time Mode after 20 seconds of inactivity.
Use the alarm switch; LCD icon indicates alarm status.
Press ALARM to display time, then hold to set hour and minute.
Confirm alarm time and set the duration for the snooze function.
Alarm automatically repeats after 24 hours if not deactivated.
Rising alarm sound with crescendo over 2 minutes.
Press any button except Snooze to stop the alarm; it will reactivate automatically.
Touch the Snooze/light button to activate snooze mode.
Switch temperature display between Celsius (°C) and Fahrenheit (°F).
Details supply voltage and adapter specifications.
Perpetual calendar range and supported time zones.
Projection distance and indoor temperature measuring range/resolution.
Specifies the accuracy for temperature measurements at different ranges.
