RECLINE 600 XTPRO: Service & Maintenance Manual - rev. 1.1
Page ii
7.3.
D
ISASSEMBLING THE
CPU
BOARD
.................................................................................................................... 7.4
7.4.
D
ISASSEMBLING THE KEYBOARD
...................................................................................................................... 7.5
7.5.
D
ISASSEMBLING THE CARDIO RECEIVER
........................................................................................................... 7.6
7.6.
D
ISASSEMBLING THE SADDLE AND RUNNER PULLEY
......................................................................................... 7.7
7.7.
D
ISASSEMBLING THE HS INTERFACE BOARD
...................................................................................................... 7.8
7.8.
D
ISASSEMBLING THE HAND SENSORS
................................................................................................................ 7.9
7.9.
D
ISASSEMBLING THE RIGHT AND LEFT SIDE CASINGS
...................................................................................... 7.10
7.10.
D
ISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS
....................................................................................... 7.11
7.11.
D
ISASSEMBLING THE ALTERNATOR
................................................................................................................. 7.12
7.12.
D
ISASSEMBLING THE BELT
.............................................................................................................................. 7.13
7.13.
D
ISASSEMBLING THE CHAIN
............................................................................................................................ 7.15
7.14.
D
ISASSEMBLING THE PULLEY
.......................................................................................................................... 7.16
7.15.
D
ISASSEMBLING THE PEDAL CRANK GROUP
.................................................................................................... 7.17
7.16.
D
ISASSEMBLING THE ALTERNATOR BRUSHES
................................................................................................. 7.18
8.
ADJUSTMENTS.................................................................................................................................................... 8.1
8.1.
B
ELT ALIGNMENT
............................................................................................................................................. 8.1
8.2.
B
ELT TENSION
.................................................................................................................................................. 8.2
8.3.
C
HAIN ALIGNMENT
........................................................................................................................................... 8.3
8.4.
C
HAIN TENSION
................................................................................................................................................ 8.4
8.5.
A
DJUSTING THE SADDLE
................................................................................................................................... 8.5
8.6.
W
EAR OF BRUSHES
........................................................................................................................................... 8.6
9.
CONFIGURING THE MACHINE ...................................................................................................................... 9.1
9.1.
U
SER SETTING PARAMETERS
............................................................................................................................. 9.1
9.1.1.
Language used .................................................................................................................................. 9.1
9.1.2.
Measurement system ......................................................................................................................... 9.1
9.1.3.
Maximum time................................................................................................................................... 9.2
9.1.4.
Activating the “+” and “
−
” keys...................................................................................................... 9.2
9.1.5.
Disabling the function keys ............................................................................................................... 9.2
9.1.6.
Enabling the “ENTER” key .............................................................................................................. 9.3
9.1.7.
Setting the priority ............................................................................................................................ 9.3
9.2.
T
ECHNICAL SETTING PARAMETERS
................................................................................................................... 9.3
9.2.1.
Enabling use of the hand sensor ....................................................................................................... 9.3
9.2.2.
Enabling the display mode................................................................................................................ 9.4
9.3.
M
AINTENANCE INFORMATION
.......................................................................................................................... 9.4
9.3.1.
Hours on............................................................................................................................................ 9.4
9.3.2.
Hours of use ...................................................................................................................................... 9.4
9.4.
C
HANGING THE MAINTENANCE INFORMATION
.................................................................................................. 9.5
9.4.1.
Hours on............................................................................................................................................ 9.5
9.4.2.
Hours of use ...................................................................................................................................... 9.5
10.
SCHEDULED MAINTENANCE ....................................................................................................................... 10.1
10.1.
E
XTERNAL CLEANING OPERATIONS
................................................................................................................. 10.1
10.1.1.
Setting up the operation .................................................................................................................. 10.1
10.1.2.
Cleaning operations ........................................................................................................................ 10.1
10.2.
R
OUTINE MAINTENANCE OPERATIONS
............................................................................................................ 10.2
10.2.1.
Setting up the operation .................................................................................................................. 10.2
10.2.2.
Internal Cleaning operations .......................................................................................................... 10.2
10.2.3.
Saddle cleaninig operation.............................................................................................................. 10.2
10.3.
S
PECIAL MAINTENANCE OPERATIONS
.............................................................................................................. 10.3
10.3.1.
Setting up the operation .................................................................................................................. 10.3
10.3.2.
Checking the working conditions .................................................................................................... 10.3
10.3.3.
Performing the routine maintenance procedure.............................................................................. 10.3
10.3.4.
Checking the wiring and connections.............................................................................................. 10.3
10.3.5.
Checking the display........................................................................................................................ 10.3
10.3.6.
Checking the wear of the rubber handlebar cover .......................................................................... 10.4
10.3.7.
Checking the state of wear of the chain........................................................................................... 10.4
To Next Page